Catalog / BOSCH / 0445110236
BOSCH

0445110236

View Specs
SolenoidBosch Common Rail (CRI2 solenoid, 0445110 series)Euro 5

Injector Fiat 1.3 D Multijet 55197824 Specs

Reference data for BOSCH 0445110236 common rail injector · OEM 55197824, 55197825, 55197124, 71793011, 93183910, 93184169, 93190435, 5821102, 15310-84E60, 1538758, 9S51-9F593-BA · Application Fiat SDE 1.3 MultiJet / Opel 1.3 CDTI / Ford 1.3 TDCi
OE REFERENCE55197824, 55197825, 55197124, 71793011, 93183910, 93184169, 93190435, 5821102, 15310-84E60, 1538758, 9S51-9F593-BA
CONTROL VALVEF00VC01325
NOZZLEDLLA153P1463
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Bosch 0445110236 is an OEM second-generation common rail electromagnetic solenoid injector (system designation CRI2-16) engineered for the small-displacement 1.3-liter common rail turbo diesel family. Co-developed under the Fiat-GM Powertrain alliance and widely commercialized across Europe as the Fiat 1.3 Multijet, Opel/Vauxhall 1.3 CDTI, Ford 1.3 Duratorq TDCi, and Suzuki 1.3 DDiS, this injector operates at hydraulic rail pressures up to 1,600 bar (23,200 PSI). Constructed around a rapid-response electromagnetic actuator with an internal coil resistance of 0.25 - 0.50 Ω, the injector utilizes high-precision hydraulic servo valves to execute pilot, main, and post-injection events per engine combustion cycle. Meeting stringent Euro 4 and Euro 5 passenger car emissions targets, it delivers clean atomization into small-bore aluminum-alloy combustion chambers.

Before You Order

Always verify the OE reference 55197824, 55197825, 55197124, 71793011 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 0445110236 needs its calibration code transferred after fitting; read the code from the new unit and program it with a compatible diagnostic tool.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Fiat Grande Punto / Punto Evo199A2000 / 199A30002005-2012
Fiat Panda II / 500 / Doblo / Fiorino169A1000 / 188A90002005-2012
Opel Corsa DZ13DTJ / Z13DTH2006-2011
Opel Astra H / Meriva A / Combo CZ13DT / Z13DTH2005-2010
Lancia Ypsilon / Musa199A2000 / 199A30002005-2011
Ford Ka II 1.3 Duratorq TDCi169A1000 75hp2008-2016
Suzuki Swift III / SplashZ13DTJ 75hp2005-2011
04

Technical Specifications

SpecificationValue
Production SKU0445110236 / 0 445 110 236
Remanufactured SKU0986435165 / 0 986 435 165
Sister SKUs0445110288, 0445110296
System ArchitectureBosch Common Rail Injector Generation 2 (CRI2-16)
Actuator TypeElectromagnetic Solenoid (Coil Resistance 0.25 - 0.50 Ω)
Operating PressureCore Spec
Control ValveCore Spec
Nozzle CodeCore Spec
Nozzle Retaining NutCore Spec
Nozzle Pressure SpringCore Spec
Injector Hold-Down Bolt Torque25-30 N·m📐 Torque & Angle Wizard →
Fuel Line Nut Torque25-28 N·m
Copper Washer Thickness1.5 mm (15.0 mm OD × 7.1 mm ID)
IMA Coding RequiredYes (6-Character IMA / IQA Code)
Engine Control UnitMagneti Marelli MJD 6JF / 6F3 / 8DF
05

Installation Tips

  1. Bore Preparation & Seating Surface: Scrape and brush carbon residue from the cylinder head injector bore using an engine-specific brass bore brush. Vacuum out all debris. Inspect the bottom copper seat with an inspection mirror; ensure bare, flat aluminum metal with zero carbon pitting.
  2. Thermal Washer & Anti-Seize: Always install a brand-new OEM copper washer (15.0 × 7.1 × 1.5 mm). Lightly coat the outer cylindrical body of the injector with high-temperature white ceramic anti-seize paste (do not allow paste to contact the nozzle tip or fuel inlet).
  3. Hold-Down Clamp Fastener Torque: Slide the injector hold-down clamp into position. Thread the M8 fastener by hand to verify clean thread engagement. Torque the clamp bolt progressively: Final Clamp Torque: 25 - 30 N·m (18 - 22 lb·ft). Do not over-torque; the aluminum head threads will strip if exceeded.
  4. Counter-Held High-Pressure Pipe Tightening: Align the high-pressure steel fuel line into the injector inlet cone by hand. Counter-hold the injector inlet hexagon with an open-ended wrench while tightening the union nut with a flare nut torque wrench to 25 - 28 N·m (18 - 21 lb·ft). Single-wrench tightening twists the injector body, straining the internal alignment dowels.
  5. MultiECUScan / Scanner IMA Coding: Read the 6-character alphanumeric IMA code laser-etched on the plastic electrical connector head. Connect a diagnostic tool (MultiECUScan for Fiat/Alfa, OP-COM for Opel, or VCM-II for Ford). Navigate to Engine ECU -> Adjustments -> Injector Coding. Input the new code for the corresponding cylinder and perform key-off reset for 30 seconds.
  6. Low-Pressure Bleeding & Leak Check: Cycle the ignition key between OFF and ON 5 to 6 times (leaving ON for 10 seconds each) to allow the in-tank electric lift pump to purge air through the filter and high-pressure pump. Crank the engine, bring to operating temperature, and inspect all union nuts and return T-pieces with a dry tissue.
Tips & Warnings:
  • Confirm the exact vehicle and engine application against the EPC before ordering.
  • Keep the replacement injector clean and inspect the old unit for external damage during removal.
  • Check the workshop manual for any matching or adaptation procedure before startup.
06

Frequently Asked Questions

QWhich vehicles does this injector fit?

It is listed for Fiat Grande Punto, Punto Evo, Panda, Doblo and Fiorino applications, plus Opel Corsa D, Astra H, Meriva A and Combo C. Confirm the exact engine variant against the vehicle's EPC before ordering.

QWhat symptoms point to a failed injector?

This listing does not state specific failure symptoms. Diagnose rough running, poor starting or misfire with the vehicle's workshop data and confirm the fault before replacing the injector.

QWhat should I check before ordering?

Check the vehicle model, engine variant and existing injector part number against the EPC or workshop manual. The listing only identifies 0445110236, so confirm that this exact unit matches the application before ordering.

QDoes the replacement need coding or adaptation?

Coding or adaptation requirements are not stated for this injector. Confirm whether matching is needed against the vehicle's EPC or workshop manual before fitting, and follow the specified procedure.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol