0445110808
Bosch Hyundai 1.7 CRDi Injector 33800 2A760 Data
0445110809, 33800-2A760, 33800-2A700, 33800-2A780, 0445110807F00VC01371DLLA148P24692000 bar peak rail pressureProduct Overview
The Bosch 0445110808 (Hyundai / Kia OE part numbers 33800-2A760, 33800-2A700, 33800-2A780, and aftermarket exchange reference 0986435299) is an advanced generation electro-hydraulic common rail diesel fuel injector from the high-pressure Bosch CRI2-20 platform. Engineered specifically for Hyundai Motor Group's 4-cylinder U2 1.7 CRDi (D4FD) and R-Series 2.0 CRDi (D4HA) turbocharged electronic diesel engines, it complies with strict European Euro 5 and Euro 6 passenger vehicle emissions regulations. Operating at class-leading peak rail injection pressures up to 2000 bar (29,000 psi), this injector executes rapid multi-pulse injections: dual pilot injections for combustion noise reduction, calibrated main injection for maximum torque efficiency, and precision post-injections for continuous particulate filter (DPF) soot oxidation without oil dilution. The hydraulic metering assembly utilizes an ultra-fine atomization spray nozzle DLLA148P2469 (0433172469) matched with a low-friction, high-speed balance control valve F00VC01371. Ensuring longevity requires following strict workshop installation procedures, renewing the single-use 1.5 mm copper seal washer (33818-2A000), tightening the injector clamp bolt to 30 N·m, and programming the laser-marked 7-character Bosch IMA flow calibration code into the Bosch EDC17C08 / EDC17C57 engine control unit.
Always verify the OE reference 338002A760, 338002A700, 338002A780 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 0445110808 needs its calibration code transferred after fitting; read the code from the new unit and program it with a compatible diagnostic tool.
Technical Specifications
| Specification | Value |
|---|---|
| INJECTOR TYPE | Common Rail Injector |
| SYSTEM PLATFORM | CRI |
| CONTROL VALVECore Spec | 🔗 Shared Valve (2 assemblies):0445110333 |
| NOZZLE CODECore Spec | |
| OPERATING PRESSURECore Spec |
Installation Tips
- Bore Inspection & De-Carbonizing: Use an injector bore cleaning brush kit to extract carbon soot from the cylinder head well. Inspect the washer sealing step at the bottom of the bore with a borescope; it must be completely flat, bare metal, and free of radial scour marks.
- Copper Seal Replacement: Always install a brand-new genuine 1.5 mm copper crush gasket (Hyundai part 33818-2A000 / 33818-27000) onto the injector nozzle shank. Never reuse old copper washers, as work-hardening prevents effective gas sealing at 2000 bar.
- Injector Insertion: Apply a light smear of high-temperature ceramic mounting grease (Bosch injector paste) to the injector body shaft, strictly keeping the nozzle tip and copper washer free of grease. Slide the injector smoothly into the bore.
- Hold-Down Clamp Torquing: Position the injector clamp fork squarely onto the injector shoulder. Thread the clamp bolt by hand, then torque with a calibrated torque wrench to 30 N·m (workshop tolerance: 28 ~ 32 N·m).
- High-Pressure Fuel Pipe Alignment: Hand-thread both fuel rail pipe nuts to prevent cross-threading, then tighten both ends evenly to 28 N·m.
- Return Leak-Off Connection: Connect the plastic leak-off spill rail, ensuring the locking retaining clip engages with an audible click.
- Verify fitment for the listed Hyundai/Kia U2 CRDi applications before installation.
- Torque the mounting / hold-down fasteners to 28-32 N·m.
- Torque the high-pressure line to 28-32 N·m.
Frequently Asked Questions
Which Hyundai and Kia 1.7 CRDi vehicles use Bosch injector 0445110808?
Bosch 0445110808 is engineered for Hyundai and Kia 1.7 CRDi (D4FD U2 engine, 85-104 kW / 115-141 hp Euro 5 / Euro 6) diesel vehicles. It fits Hyundai Tucson / ix35, Hyundai i40, Kia Sportage III and IV, Kia Optima / K5, and Kia Carens IV from 2010 to 2019.
What are the genuine Hyundai and Kia OE part numbers for Bosch 0445110808?
Genuine OEM part numbers are 33800-2A760, 33800-2A700, and 33800-2A780, with Bosch exchange reference 0986435299. It operates on the high-pressure Bosch CRI2-20 platform with operating pressures up to 2,000 bar.
What tightening torque is required for Hyundai/Kia 1.7 CRDi injector clamp bolts?
Tighten the M7 hold-down clamp bolt to 28-32 N·m. Replace the hold-down bolt and the 1.5 mm copper washer at every service. Ensure high-pressure fuel rail line nuts are tightened to 25-30 N·m.
Is Bosch IMA coding required on Hyundai D4FD 1.7 CRDi engines?
Yes. Each Bosch 0445110808 injector carries a 7-character alphanumeric IMA code laser-etched onto the electrical connector. Input this code into the Bosch EDC17C08 or EDC17C57 ECU using Hyundai/Kia GDS, G-Scan, or Bosch KTS to prevent rough idle and excessive exhaust emissions.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.