BOSCH 0445120217
Common Rail Injector for MAN TGX TGS TGA D2066 10.5L
51101006064, 51101006126, 51101009126F00RJ02466DLLA148P15241600 bar peak rail pressureProduct Overview
The Bosch 0445120217 is a heavy-duty CRIN2-16 commercial vehicle common rail diesel fuel injector engineered for MAN TGX, TGS, and TGA heavy-duty trucks powered by the 10.5L D2066 inline-six turbodiesel engine family (variants D2066 LF11 to LF35, rated from 235 kW / 320 HP to 324 kW / 440 HP). Operating at fuel rail pressures up to 1600 bar, this assembly features precision hole-type nozzle 0433171939 (stamped DLLA148P1524), control valve set F00RJ02466, and electromagnetic actuator F00RJ02703 to deliver calibrated multi-pilot and main injection events meeting Euro 4 and Euro 5 (EEV) emissions. Common workshop failure patterns under high operating hours include excessive dynamic fuel backleakage into the return manifold, prolonged hot cranking, black exhaust plume under heavy gradient payload, and diagnostic trouble code P0087 accompanied by engine limp-home derate.
CRITICAL FEED TUBE SEQUENCE: Never torque the hold-down clamp before seating the high-pressure connector tube. Pre-torque the connector tube retaining nut to 15 N·m first to align the spherical sealing interface with the injector inlet port, torque the hold-down clamp bolt to 26-30 N·m, and finally torque the connector tube nut to 50-55 N·m to prevent internal high-pressure fuel leakage into the cylinder head and fault code P0087.
Technical Specifications
| Specification | Value |
|---|---|
| Injection System | Bosch CRIN2-16 |
| Operating Rail PressureCore Spec | |
| Nozzle Part NumberCore Spec | 🔗 Shared Nozzle (2 assemblies):0445120061 |
| Nozzle CodeCore Spec | 🔗 Shared Nozzle (2 assemblies):0445120061 |
| Control Valve AssemblyCore Spec | 🔗 Shared Valve (2 assemblies):0445120219 |
| Magnet Assembly | F00RJ02703 |
| Seal Ring Kit | F00RJ02176 |
| Injector Hold-Down Bolt Torque | 26-30 N·m📐 Torque & Angle Wizard → |
| Connector Tube Torque | 50-55 N·m |
| IMA Coding Required | No (Non-IMA hydraulic calibration unit) |
| Factory Warranty | 12 Months |
Installation Tips
- Depressurize And Isolate: Depressurize the fuel system and isolate the fuel supply, then clean the cylinder head, injector bore, high-pressure line, and connector tube area before opening any connection.
- Disconnect Connections And Remove Line: Disconnect the electrical connector and spill connection, remove the high-pressure line from the injector and connector tube, and cap or plug all opened ports to prevent debris entry.
- Extract Old Unit: Remove the old injector from the injector bore, discard the old copper combustion washer, and clean the bore and seat so the new copper combustion washer and seals can seat correctly.
- Fit New Seals: Fit new seals and a new copper combustion washer, lubricate only as permitted by the service information, and seat the injector in the injector bore without damaging the sealing surfaces.
- Pre-Tighten Connector Tube: Pre-torque the connector tube to 15 N·m and seat the spherical interface before tightening the hold-down.
- Tighten Hold-Down And Line: With the connector tube pre-torqued and spherical interface seated, tighten the hold-down to 26-30 N·m; torque the connector tube finally to 50-55 N·m; reconnect the high-pressure line and tighten it to 30-35 N·m.
- Leak-Check And Start-Up: After installation, check for leaks at the high-pressure line, connector tube, and injector joint using the approved leak-check method, then start the engine and inspect for abnormal running or leaks.
- Tighten the injector mounting / hold-down to 26-30 N·m.
- Tighten the high-pressure line to 30-35 N·m.
- Verify part number 0445120217 and its listed cross references against the vehicle's EPC before fitting.
Frequently Asked Questions
Will this injector 0445120217 fit my MAN truck or bus?
It is listed for the MAN D2066 LF / LOH (10.5L Common Rail) engine family in MAN TGX and TGS (2007-2016), MAN TGA (2006-2011), and MAN Lion's City / Lion's Coach (2006-2016). Confirm the exact vehicle variant against the vehicle's EPC before ordering.
Which diagnostic trouble codes are listed for this common-rail diesel injector?
The listed codes are P0300, P0301, P0302, P0304, and P0087. Confirm any further fault-code interpretation against the vehicle's EPC rather than guessing.
Does this injector need coding or adaptation after installation?
Coding/adaptation requirements for part 0445120217 are not stated in the supplied facts. Confirm the required procedure against the vehicle's EPC before installation.
How can I verify the old injector and cross-reference numbers before replacement?
Check the old unit for part number 0445120217 and compare it with the listed cross references: 51101006064, 51101006126, 51101009126, 0445120030, and 0445120061. Confirm the exact application against the vehicle's EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.