BOSCH 0445120397
Common Rail Injector for FAW Jiefang J6 & FAWDE CA6DM2 11L
1112010-M10-0000F00RJ02035DLLA151P22401600 bar peak rail pressureProduct Overview
The Bosch 0445120397 is an updated heavy-duty CRIN2-16 common rail diesel fuel injector engineered for high-output commercial transport applications powered by FAWDE Xichai Aowei CA6DM2 (11.1L) turbodiesel platforms. Serving as the primary direct factory replacement and production update for injector 0445120277 across FAW Jiefang J6P, JH6, J6M, and J5P heavy tractor units, this injector operates at injection pressures up to 1600 bar. The hydraulic circuit incorporates control valve assembly F00RJ02035 and multi-hole nozzle 0433172240 (stamped DLLA151P2240) to satisfy Euro 4 and Euro 5 heavy commercial emission standards. Common field failure symptoms include excessive dynamic backleakage into the fuel return rail, extended hot-cranking, unburned black exhaust smoke under acceleration, and engine hesitation under heavy haul grades.
CRITICAL CONNECTOR TUBE TORQUE SEQUENCE: Never tighten the hold-down clamp bolt before seating and pre-torquing the high-pressure connector tube. Pre-torque the connector tube nut to 15 N·m first to ensure spherical alignment with the injector inlet port, torque the hold-down clamp bolt to 24 N·m, and finally torque the connector tube nut to 50-55 N·m. Improper torque progression causes internal fuel bypass past the O-ring seal, engine oil dilution, and rail pressure drop fault P0087.
Vehicle & Engine Fitment
Technical Specifications
| Specification | Value |
|---|---|
| Manufacturer | BOSCH |
| Part Number | 0445120397 |
| System Type | Common Rail Heavy Commercial Injector (CRIN2-16) |
| Engine Platform | FAWDE Xichai Aowei CA6DM2 (11.1L) |
| Engine Codes | CA6DM2-39E4, CA6DM2-42E4, CA6DM2-46E4, CA6DM2-39E5, CA6DM2-42E5 |
| Emission Standard | Euro 4 / Euro 5 |
| Operating PressureCore Spec | |
| Nozzle CodeCore Spec | 🔗 Shared Nozzle (2 assemblies):0445120277 |
| Nozzle Part NumberCore Spec | 🔗 Shared Nozzle (2 assemblies):0445120277 |
| Control Valve AssemblyCore Spec | 🔗 Shared Valve (2 assemblies):0445120277 |
| OE Part Number | 1112010-M10-0000 |
| Injector Hold-Down Clamp Torque | 24 N·m📐 Torque & Angle Wizard → |
| Connector Tube Pre-Torque | 15 N·m |
| Connector Tube Torque | 50-55 N·m |
| Fuel Line Nut Torque | 30-35 N·m |
| Warranty | 12 Months |
Installation Tips
- Depressurize And Isolate: Depressurize the high-pressure fuel system according to workshop instructions, isolate the supply, and prevent cranking before opening any high-pressure connection.
- Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before disconnecting the electrical connector and spill return connection, then cap open ports to keep contaminants out.
- Remove Line And Extract: Remove the high-pressure line from the injector and high-pressure connector tube, then extract the old unit carefully from the injector bore without damaging the seat.
- Clean Bore And Fit Seals: Clean the injector bore and seat in the cylinder head, remove all residue, and fit new seals including a new copper combustion washer to the replacement injector.
- Seat And Pre-Torque Tube: Seat the injector squarely in the injector bore, pre-torque the high-pressure connector tube to 15 N·m, and seat the spherical interface before any hold-down tightening.
- Tighten Hold-Down And Reconnect: Tighten the hold-down to 24 N·m, torque the connector tube finally to 50-55 N·m, then reconnect the high-pressure line and tighten it to 30-35 N·m.
- Calibration Coding: Record the new injector calibration code and program it with a compatible diagnostic tool.
- Leak-Check And Start-Up: After calibration coding, perform a leak check of the high-pressure line and connector tube joints, then start the engine and inspect for leaks, abnormal noise, and faults.
- Apply the listed 24 N·m mounting / hold-down torque to this common-rail diesel injector.
- Tighten the high-pressure line for part 0445120397 to 30-35 N·m.
- Confirm fitment for FAW Jiefang J6P, JH6, J6M, and J5P with CA6DL1, CA6DL2, or CA6DM2 against the vehicle's EPC before installation.
Frequently Asked Questions
Is 0445120397 completely interchangeable with 0445120277?
Yes. Bosch 0445120397 is the direct factory production update and interchangeable supersession for 0445120277 on FAWDE CA6DM2 (11.1L) Euro 4 and Euro 5 platforms. Both injectors utilize nozzle DLLA151P2240 (0433172240), valve F00RJ02035, and OE reference 1112010-M10-0000. They can be mixed across cylinders or replaced as a complete balanced set.
What is the correct installation torque sequence for the CA6DM2 connector tube?
Follow the standard 3-step sequence: Step 1, hand-thread the connector tube and pre-torque its retaining nut to 15 N·m; Step 2, torque the injector hold-down clamp bolt to 24 N·m; Step 3, perform final torque on the connector tube nut to 50-55 N·m. Finally torque the fuel supply line union nut to 30-35 N·m.
Can this injector be used on FAW Jiefang with CA6DL 8.6L engines?
No. FAWDE CA6DL engines (7.7L and 8.6L) require injector 0445120393 (OE 1112010-630) equipped with nozzle DLLA150P1622 and valve F00RJ01657. Installing 0445120397 into an 8.6L engine will result in fuel over-delivery and combustion knock.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.