Catalog / CONTINENTAL / A2C59511364
CONTINENTAL

Continental VDO A2C59511364

View Specs
SolenoidContinental / VDO Common RailEuro 4

Piezo Common Rail Injector

Reference data for CONTINENTAL A2C59511364 common rail injector · OEM LR006495, 4H2Q-9K546-AE, C2C24798 · Application 2.7 TDV6, Lion V6, 276DT
OE REFERENCELR006495, 4H2Q-9K546-AE, C2C24798
CONTROL VALVE-
NOZZLEM0018P155
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Continental Siemens VDO A2C59511364 is an authentic piezoelectric common rail diesel injector calibrated for Land Rover Discovery 3 (L319) and 2.7 TDV6 engine platforms. Operating at an engineered rail pressure of 1650 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.

Before You Order

Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Land Rover Discovery 3 (L319)2.7 TDV6 (276DT)2004-2009
Land Rover Range Rover Sport (L320)2.7 D 4x4 (276DT)2005-2013
Jaguar S-Type (X200)2.7 D (AJD)2004-2007
04

Technical Specifications

SpecificationValue
SKUA2C59511364
BrandCONTINENTAL
Fuel SystemContinental / VDO Common Rail
Operating PressureCore Spec
Hold Down Torque10 N·m + 90°
High-Pressure Line Torque30 N·m
Coding RequiredVDO 6-Hex IIC
Emission StandardEuro 4
Injector TypePiezoelectric
05

Installation Tips

  1. Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
  2. Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
  3. Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
  4. Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
  5. Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
  6. Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 10 N·m, then rotate a further 90°, then reconnect the high-pressure line to the injector and tighten the line fitting to 30 N·m; keep the line aligned and free from side load.
  7. Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
  8. Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
Tips & Warnings:
  • Tighten the mounting/hold-down to 10 N·m + 90°.
  • Tighten the high-pressure line to 30 N·m.
  • Check the part number A2C59511364 and cross references 5WS40200, LR006495, 4H2Q-9K546-AE, and C2C24798 before fitting.
06

Frequently Asked Questions

QWhich vehicles is part A2C59511364 listed for?

It is listed for Land Rover Discovery 3 (L319) 2.7 TDV6 (276DT) 2004-2009 and Land Rover Range Rover Sport (L320) 2.7 D 4x4 (276DT) 2005-2013. It is also listed for Jaguar S-Type (X200) 2.7 D (AJD) 2004-2007. Confirm fitment against the vehicle EPC.

QWhat diagnostic trouble codes are associated with this common-rail diesel injector?

The listed diagnostic trouble codes are P0300, P0087, P0201, P0204, and P0202. Symptom-to-code mapping and a definitive failed-unit diagnosis are not stated, so confirm them against the vehicle diagnostics and EPC.

QDo I need to code or adapt this injector after fitting?

Coding or adaptation requirements are not stated in the verified facts. Confirm coding or adaptation requirements against the vehicle EPC and diagnostic procedures before fitting.

QHow can I verify the old injector matches this listing?

Check the old unit for part number A2C59511364 and compare any cross references 5WS40200, LR006495, 4H2Q-9K546-AE, or C2C24798. If markings are unclear, confirm fitment against the vehicle EPC rather than guessing.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

P0300High

Random or Multiple Cylinder Misfire Detected

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

CRDI WORKSHOP ENGINEERING & DIAGNOSTICS

Piezo Injector 10 Bar Backleak & Stalling Guide

Bosch CRI3 piezo injector 10 bar backleak pressure guide. Diagnose hydraulic coupler cavitation, overflow valve failure, return line stalling & P0087.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol