Continental VDO A2C59511600
High Pressure Fuel Pump
1980E6, 9651590880X39-800-300-005Z-1350 bar peak rail pressureProduct Overview
Continental VDO A2C59511600 is an authentic high-pressure common rail diesel injection supply pump engineered for Peugeot 307 (3A/C) and 2.0 HDi applications. Operating at up to 1350 bar under Euro 3 emission control, this precision unit incorporates electronic volume control (VCV) and pressure control (PCV) valves for accurate rail pressure regulation.
Verify VCV/PCV valve connections and high pressure line torque before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | A2C59511600 |
| Brand | CONTINENTAL |
| Fuel System | Continental / VDO Common Rail |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Hold Down Torque | 22 N·m |
| High-Pressure Line Torque | 50 N·m (Sprocket) / 22 N·m (Flange) |
| Emission Standard | Euro 3 |
| System Type | High Pressure Fuel Pump |
Installation Tips
- Depressurize And Isolate: Depressurize the high-pressure fuel system according to the service data, isolate the battery and fuel supply, and place a suitable container for spillage before beginning work.
- Clean Surrounding Area: Clean the pump mounting area, the high-pressure line connections, the low-pressure connections and the surrounding area of the cylinder head before loosening any fastener, then dry with lint-free material and keep all openings capped.
- Disconnect Connections: Disconnect the electrical connector, the spill connection and the low-pressure connections, then cap all open ports and protect the surrounding area from fuel spillage.
- Remove High-Pressure Line: Remove the high-pressure delivery line from the pump outlet, cap all open ports immediately, and discard the sealing washers if fitted; do not reuse the line if it is deformed or damaged.
- Extract Old Unit: Remove the drive coupling or sprocket, remove the pump flange fasteners, extract the old unit from its mounting bore, clean the bore and seat in the cylinder head, inspect the drive contact (roller follower, tappet or coupling as fitted) for wear or damage, and fit new seals to the pump flange.
- Seat And Tighten Unit: Seat the unit squarely in the bore, engage the drive coupling or sprocket, fit the hold-down and flange fasteners, tighten the pump flange fasteners to 22 N·m, and tighten the refitted drive coupling or sprocket to 50 N·m.
- Leak-Check And Start-Up: Reconnect the high-pressure delivery line and tighten the line to the torque specified in the service data, reconnect the low-pressure connections and electrical connector, then start the engine, check for leaks at the pump, lines and connections, and rectify any leak before returning the system to service.
- Clean the fuel system and replace contaminated components before fitting a replacement high-pressure pump.
- Record the label part number A2C59511600 and compare it with the unit removed from the vehicle.
- Use the vehicle's workshop data to confirm tightening and diagnostic procedures; do not guess.
Frequently Asked Questions
Will this pump fit my Peugeot or Citroen?
Confirm fitment against the listed RHY/RHZ applications and your vehicle's EPC or workshop manual before ordering; the label must show A2C59511600.
What symptoms suggest the high-pressure pump has failed?
Look for hard starting, poor power, fuel-pressure-related fault codes, metal debris in the fuel system, or a no-start condition; confirm diagnosis with workshop testing before replacement.
What should I check before ordering?
Check the engine code matches RHY or RHZ, verify the housing and connector against the old unit, inspect for contamination, and confirm the part number A2C59511600 on the label.
Must the replacement pump be coded or adapted?
Coding or adaptation requirements are not stated here; confirm against the vehicle's EPC or workshop manual. Also check whether the old unit must be matched to the vehicle.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.