Catalog / CONTINENTAL / A2C59511611
CONTINENTAL

Continental VDO A2C59511611

View Specs
SolenoidContinental / VDO Common RailEuro 4

Piezo Common Rail Injector

Reference data for CONTINENTAL A2C59511611 common rail injector · OEM 1980EA, 9654551080, 1364771 · Application 1.4 HDi, DV4TD, 8HX, 8HZ
OE REFERENCE1980EA, 9654551080, 1364771
CONTROL VALVE-
NOZZLEM1003P152
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Continental Siemens VDO A2C59511611 is an authentic piezoelectric common rail diesel injector calibrated for Peugeot 206 (2A/C) and 1.4 HDi engine platforms. Operating at an engineered rail pressure of 1500 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.

Before You Order

Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Peugeot 206 (2A/C)1.4 HDi (8HX)2001-2009
Citroen C3 I (FC_)1.4 HDi (8HX)2002-2010
Ford Fiesta V (JH_, JD_)1.4 TDCi (F6JA)2001-2008
04

Technical Specifications

SpecificationValue
SKUA2C59511611
BrandCONTINENTAL
Fuel SystemContinental / VDO Common Rail
Operating PressureCore Spec
Hold Down Torque25 N·m
High-Pressure Line Torque25 N·m
Coding RequiredVDO 6-Hex IIC
Emission StandardEuro 4
Injector TypePiezoelectric
05

Installation Tips

  1. Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
  2. Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
  3. Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
  4. Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
  5. Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
  6. Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 25 N·m, then reconnect the high-pressure line to the injector and tighten the line fitting to 25 N·m; keep the line aligned and free from side load.
  7. Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
  8. Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
Tips & Warnings:
  • Confirm fitment, coding and adaptation requirements for A2C59511611 against the vehicle's EPC or workshop manual before installation.
  • Keep the common-rail injector clean and follow the vehicle's workshop procedure; do not assume seal reuse or service life.
  • If diagnosis is unclear, verify the fault against the vehicle's workshop data before replacing A2C59511611.
06

Frequently Asked Questions

QWill A2C59511611 fit my Peugeot, Citroen or Ford?

It is listed for the HDi/TDCi Peugeot, Citroen and Ford applications shown in the fitment data; confirm your exact engine code against the vehicle's EPC before ordering A2C59511611.

QWhat symptoms indicate a failed A2C59511611?

The listing does not specify failure symptoms. Diagnose common-rail faults against the vehicle's workshop data before replacing A2C59511611.

QWhat should I check before ordering A2C59511611?

Check the exact engine code and fitment listing, inspect the injector connector and rail area, and confirm any coding or adaptation requirements against the vehicle's EPC or workshop manual before ordering A2C59511611.

QMust the old injector be matched or adapted to the vehicle?

The listing does not state whether matching or adaptation is required. Confirm this against the vehicle's EPC or workshop manual before fitting A2C59511611.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

P0300High

Random or Multiple Cylinder Misfire Detected

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

CRDI WORKSHOP ENGINEERING & DIAGNOSTICS

Piezo Injector 10 Bar Backleak & Stalling Guide

Bosch CRI3 piezo injector 10 bar backleak pressure guide. Diagnose hydraulic coupler cavitation, overflow valve failure, return line stalling & P0087.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol