Continental VDO A2C59511612
Piezo Common Rail Injector
1980E5, 9636680280-M0604P1421350 bar peak rail pressureProduct Overview
The Continental Siemens VDO A2C59511612 is an authentic piezoelectric common rail diesel injector calibrated for Peugeot 406 (8B) and 2.0 HDi engine platforms. Operating at an engineered rail pressure of 1350 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.
Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | A2C59511612 |
| Brand | CONTINENTAL |
| Fuel System | Continental / VDO Common Rail |
| Operating PressureCore Spec | |
| Hold Down Torque | 30 N·m |
| High-Pressure Line Torque | 30 N·m |
| Coding Required | VDO 6-Hex IIC |
| Emission Standard | Euro 3 |
| Injector Type | Piezoelectric |
Installation Tips
- Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
- Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
- Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
- Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
- Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
- Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 30 N·m, then reconnect the high-pressure line to the injector and tighten the line fitting to 30 N·m; keep the line aligned and free from side load.
- Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
- Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
- Confirm the engine code and injector part number A2C59511612 before removal to avoid fitting the wrong unit.
- Use the vehicle's workshop data for torque, seal replacement, and any coding or adaptation procedure.
- Inspect the fuel system and electrical connector condition before installing the replacement injector.
Frequently Asked Questions
Which vehicles does A2C59511612 fit?
It is listed for the Peugeot application with the RHZ engine code and the Citroen Xsara application with the RHY engine code. Confirm exact vehicle details against the EPC or workshop manual before ordering.
What are the symptoms of a failed A2C59511612?
No failure symptoms are stated in the listing; diagnose the vehicle with live data and follow the workshop manual before replacing A2C59511612.
What should I check before ordering A2C59511612?
Check the engine code, injector part number A2C59511612, connector and body type, and whether the vehicle requires injector coding or adaptation. Verify seal and mounting hardware requirements in the EPC or workshop manual.
Must the old injector be matched or adapted for A2C59511612?
The listing does not state coding or adaptation requirements. Check with the vehicle's EPC or workshop manual and suitable diagnostic equipment whether the replacement needs matching to the engine control unit.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.