Continental VDO A2C59514911
Piezo Common Rail Injector
1483824, 7G9Q-9F593-AA--1600 bar peak rail pressureProduct Overview
The Continental Siemens VDO A2C59514911 is an authentic piezoelectric common rail diesel injector calibrated for Ford Mondeo IV (BA7) and 2.0 TDCi engine platforms. Operating at an engineered rail pressure of 1600 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.
Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | A2C59514911 |
| Brand | CONTINENTAL |
| Fuel System | Continental / VDO Common Rail |
| Operating PressureCore Spec | |
| Hold Down Torque | 4 N·m + 65° |
| High-Pressure Line Torque | 25 N·m |
| Coding Required | VDO 6-Hex IIC |
| Emission Standard | Euro 4 |
| Injector Type | Piezoelectric |
Installation Tips
- Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
- Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
- Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
- Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
- Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
- Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 4 N·m, then rotate a further 65°, then reconnect the high-pressure line to the injector and tighten the line fitting to 25 N·m; keep the line aligned and free from side load.
- Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
- Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
- Verify A2C59514911 and the listed cross references (5WS40156-4Z, 1483824, 7G9Q-9F593-AA) before installation.
- Tighten the high-pressure line to 25 N·m.
- Tighten the mounting/hold-down to 4 N·m + 65°.
Frequently Asked Questions
How do I confirm this common-rail diesel injector fits my vehicle?
Check part number A2C59514911 and cross references 5WS40156-4Z, 1483824, and 7G9Q-9F593-AA. The engine family listed is 2.0 TDCi QXBA/UFBA, while the listed vehicle fitment is Ford Mondeo IV (BA7) 2.0 TDCi (QXBA) 2007-2014 and Ford S-Max (WA6) 2.0 TDCi (QXBA) 2006-2014. If your engine code or model year is not covered by those details, confirm against the vehicle's EPC before ordering.
What diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0087, P0201, P0204, and P0202. No symptom descriptions are stated in the verified facts, so do not guess; confirm any additional diagnostic details against the vehicle's EPC.
Does this injector require coding or adaptation after installation?
Coding or adaptation requirements are not stated in the verified facts. Confirm this against the vehicle's EPC instead of guessing before installation.
What are the mounting/hold-down and high-pressure line torque values?
The mounting/hold-down torque is 4 N·m + 65°. The high-pressure line torque is 25 N·m.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.