Continental VDO A2C59514912
Piezo Common Rail Injector
1545612, 8G9Q-9F593-AA-M1003P1521600 bar peak rail pressureProduct Overview
The Continental Siemens VDO A2C59514912 is an authentic piezoelectric common rail diesel injector calibrated for Ford Kuga I and 2.0 TDCi engine platforms. Operating at an engineered rail pressure of 1600 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.
Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | A2C59514912 |
| Brand | CONTINENTAL |
| Fuel System | Continental / VDO Common Rail |
| Operating PressureCore Spec | |
| Hold Down Torque | 4 N·m + 65° |
| High-Pressure Line Torque | 25 N·m |
| Coding Required | VDO 6-Hex IIC |
| Emission Standard | Euro 4 |
| Injector Type | Piezoelectric |
Installation Tips
- Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
- Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
- Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
- Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
- Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
- Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 4 N·m, then rotate a further 65°, then reconnect the high-pressure line to the injector and tighten the line fitting to 25 N·m; keep the line aligned and free from side load.
- Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
- Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
- Confirm fitment and cross references against the vehicle's EPC before ordering.
- Tighten the mounting/hold-down to 4 N·m + 65° and the high-pressure line to 25 N·m.
- Confirm coding/adaptation and seal reuse requirements against the vehicle's EPC before installation.
Frequently Asked Questions
Will A2C59514912 fit my Ford Kuga I 2.0 TDCi (UFDA) 2008-2012 or Ford Galaxy (WA6) 2.0 TDCi (TXDA) 2006-2015?
A2C59514912 is a common-rail diesel injector listed for Ford Kuga I 2.0 TDCi (UFDA) (2008-2012) and Ford Galaxy (WA6) 2.0 TDCi (TXDA) (2006-2015). Cross references are A2C59514911, 1545612, and 8G9Q-9F593-AA. Confirm the exact vehicle and old part number against the vehicle's EPC before ordering.
What diagnostic trouble codes are listed for this common-rail diesel injector?
The diagnostic trouble codes listed for this common-rail diesel injector are P0300, P0087, P0201, P0204, and P0202. Use them as reference and confirm the diagnosis against the vehicle's diagnostic procedure.
What is the expected service life, and does this injector require coding/adaptation?
Expected service life is not stated in the verified facts, and coding/adaptation requirements are not stated either. Confirm both against the vehicle's EPC before installation.
Can I reuse the seals, and what are the torque settings?
Reuse of seals is not stated in the verified facts, so confirm it against the vehicle's EPC. Mounting/hold-down torque is 4 N·m + 65°, and high-pressure line torque is 25 N·m. The listed system pressure is 1600 bar.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.