Continental VDO A2C59514913
Piezo Common Rail Injector
1373550, 6C1Q-9F593-AB--1600 bar peak rail pressureProduct Overview
The Continental Siemens VDO A2C59514913 is an authentic piezoelectric common rail diesel injector calibrated for Ford Transit V (V347/8) and 2.4 TDCi engine platforms. Operating at an engineered rail pressure of 1600 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.
Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Ford Transit V (V347/8) | 2.4 TDCi (PHFA) | 2006-2014 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | A2C59514913 |
| Brand | CONTINENTAL |
| Fuel System | Continental / VDO Common Rail |
| Operating PressureCore Spec | |
| Hold Down Torque | 30 N·m |
| High-Pressure Line Torque | 30 N·m |
| Coding Required | VDO 6-Hex IIC |
| Emission Standard | Euro 4 |
| Injector Type | Piezoelectric |
Installation Tips
- Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
- Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
- Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
- Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
- Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
- Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 30 N·m, then reconnect the high-pressure line to the injector and tighten the line fitting to 30 N·m; keep the line aligned and free from side load.
- Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
- Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
- Tighten the injector mounting/hold-down to 30 N·m.
- Tighten the high-pressure line to 30 N·m.
- Observe the 1600 bar system pressure when working on this common-rail diesel injector.
Frequently Asked Questions
Will this common-rail diesel injector fit my Ford Transit V (V347/8) 2.4 TDCi (PHFA) from 2006 to 2014?
Yes, the listed fitment is Ford Transit V (V347/8) 2.4 TDCi (PHFA) (2006-2014). The engine family is 2.4 TDCi, PHFA, H9FB, and the part number is A2C59514913. For any other application, confirm against the vehicle's EPC.
What diagnostic trouble codes are listed for this injector?
The verified facts list P0300, P0087, P0201, P0204 and P0202. They do not describe failure symptoms, so confirm diagnosis and any further checks against the vehicle's EPC.
Does this injector require coding or adaptation after installation?
The verified facts do not state coding or adaptation requirements. Confirm this against the vehicle's EPC before installation.
How do I verify the old part before ordering a replacement?
Compare the old unit with part number A2C59514913 and cross references 5WS40148, 1373550 and 6C1Q-9F593-AB. If it cannot be matched to these references, confirm against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.