Continental VDO A2C59517052
Piezo Common Rail Injector
CK4Q-9K546-AA, 1840747--1800 bar peak rail pressureProduct Overview
The Continental Siemens VDO A2C59517052 is an authentic piezoelectric common rail diesel injector calibrated for Ford Transit Custom (V362) and 2.2 TDCi engine platforms. Operating at an engineered rail pressure of 1800 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.
Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | A2C59517052 |
| Brand | CONTINENTAL |
| Fuel System | Continental / VDO Common Rail |
| Operating PressureCore Spec | |
| Hold Down Torque | 6 N·m + 180° |
| High-Pressure Line Torque | 30 N·m |
| Coding Required | VDO 6-Hex IIC |
| Emission Standard | Euro 5 |
| Injector Type | Piezoelectric |
Installation Tips
- Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
- Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
- Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
- Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
- Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
- Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 6 N·m, then rotate a further 180°, then reconnect the high-pressure line to the injector and tighten the line fitting to 30 N·m; keep the line aligned and free from side load.
- Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
- Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
- Verify part number A2C59517052 and cross references BK2Q-9K546-AG, CK4Q-9K546-AA, and 1840747 before fitting.
- Tighten the mounting/hold-down to 6 N·m plus 180°.
- Tighten the high-pressure line to 30 N·m.
Frequently Asked Questions
Which vehicles and engine family does this common-rail diesel injector fit?
This injector fits Ford Transit Custom (V362) 2.2 TDCi (CYFF) from 2012-2016 and Ford Tourneo Custom 2.2 TDCi (CVFF) from 2012-2016. It is listed for the 2.2 TDCi, CYFF, and CVFF engine family. The part number is A2C59517052.
Which diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0087, P0201, P0204, and P0202. Specific failure symptoms are not stated in the supplied facts, so confirm any unlisted details against the vehicle's EPC rather than guessing.
Are coding or adaptation procedures required after fitting this injector?
Coding or adaptation requirements are not stated in the supplied facts. Confirm them against the vehicle's EPC before installation instead of guessing.
What are the mounting/hold-down and high-pressure line torque specifications?
The mounting/hold-down torque is 6 N·m plus 180°. The high-pressure line torque is 30 N·m. The listed system pressure is 1800 bar.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.