Continental VDO A2C9626040080
Piezo Common Rail Injector
03L130277S, 03L130277SX-M0011P1621600 bar peak rail pressureProduct Overview
The Continental Siemens VDO A2C9626040080 is an authentic piezoelectric common rail diesel injector calibrated for Volkswagen Polo V (6R) and 1.6 TDI engine platforms. Operating at an engineered rail pressure of 1600 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.
Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Polo V (6R) | 1.6 TDI (CAYC) | 2009-2014 |
| Audi A1 (8X1) | 1.6 TDI (CAYC) | 2010-2015 |
| Seat Ibiza IV (6J5) | 1.6 TDI (CAYB) | 2009-2015 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | A2C9626040080 |
| Brand | CONTINENTAL |
| Fuel System | Continental / VDO Common Rail |
| Operating PressureCore Spec | |
| Hold Down Torque | 8 N·m + 180° |
| High-Pressure Line Torque | 25 N·m |
| Coding Required | VDO 6-Hex IIC |
| Emission Standard | Euro 5 |
| Injector Type | Piezoelectric |
Installation Tips
- Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
- Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
- Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
- Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
- Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
- Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 8 N·m, then rotate a further 180°, then reconnect the high-pressure line to the injector and tighten the line fitting to 25 N·m; keep the line aligned and free from side load.
- Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
- Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
- Match part number A2C9626040080 or the listed cross references before fitting.
- Observe the 8 N·m + 180° mounting/hold-down torque.
- Tighten the high-pressure line to 25 N·m.
Frequently Asked Questions
Will this common-rail diesel injector fit my vehicle?
It is listed for Volkswagen Polo V (6R) 1.6 TDI (CAYC) 2009-2014, Audi A1 (8X1) 1.6 TDI (CAYC) 2010-2015, and Seat Ibiza IV (6J5) 1.6 TDI (CAYB) 2009-2015. Check part number A2C9626040080 and the listed cross references against the vehicle's EPC before ordering.
What fault codes are associated with this injector listing?
The verified facts list diagnostic trouble codes P0300, P0087, P0201, P0204, and P0202 for this listing. Specific symptoms are not stated, so confirm the diagnosis against the vehicle's EPC and diagnostic information instead of guessing.
Does this injector need coding or adaptation after installation?
The verified facts do not state coding or adaptation requirements for this common-rail diesel injector. Confirm the correct procedure against the vehicle's EPC and diagnostic information before fitting instead of guessing.
Can I reuse the seals, and what torque values apply?
The verified facts do not state whether the seals can be reused, so confirm seal reuse against the vehicle's EPC and service information. The mounting/hold-down torque is 8 N·m + 180°, and the high-pressure line torque is 25 N·m.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.