Catalog / DENSO / 095000-6070
DENSO

095000-6070

View Specs
SolenoidDenso Common Rail System (CRS)Euro 4

Denso Komatsu 6D125 Injector 6251 11 3100

Reference data for DENSO 095000-6070 common rail injector · OEM 6251-11-3100 · Application Komatsu 6D125 (11.0L 6-Cylinder)
OE REFERENCE6251-11-3100
CONTROL VALVEPLATE #10
NOZZLEDLLA148P915
RAIL PRESSURE-
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Denso 095000-6070 is an original-equipment electro-hydraulic common rail diesel fuel injector from the Denso G2 architecture, fitted to the Komatsu 6D125 six-cylinder industrial diesel engine (11.0 L) used in PC400-8 and PC450-8 hydraulic excavators. Komatsu genuine part number 6251-11-3100 identifies this injector; Denso aftermarket reference DCRI106070 is also used. The internal hydraulic assembly carries a DLLA148P915 atomizing nozzle (Denso 093400-9150) and a multi-hole electro-hydraulic control valve. Because this engine sees continuous heavy-duty hydraulic load, injector performance depends on a clean sealing seat, a new copper seat washer at every installation, and correct transfer of the injector calibration code into the ECM. Always confirm the application against the machine serial number before ordering: the same Denso family serves several displacements and the injector bodies are not interchangeable between them.

Before You Order

Before ordering, read the numbers stamped on the existing injector body and confirm they match 095000-6070 / 6251-11-3100 for your machine. Confirm the engine code (6D125) and the machine model against the serial-number plate, not against the listing alone. This injector carries a calibration code that must be transferred to the ECM after fitting; record it before the unit is installed.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
Aftermarket
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Komatsu PC400-86D1252006-2015
Komatsu PC450-86D1252006-2015
04

Technical Specifications

SpecificationValue
SKU095000-6070
BrandDENSO
Component TypeG2 Common Rail Fuel Injector
OE Number6251-11-3100, 6251113100, DCRI106070
Fuel SystemDenso Common Rail System (CRS G2)
Engine FamilyKomatsu 6D125 (11.0L 6-Cylinder)
Warranty12 Months
Coding RequiredYes (Denso calibration code / Komatsu diagnostic tool)
Emission StandardEPA Tier 3 / EU Stage IIIA
05

Installation Tips

  1. Seat preparation: clean the injector bore sleeve with lint-free cloths; inspect the spherical sealing face of the high-pressure connector tube for wear or radial indentation and replace it if ring grooves are visible.
  2. Seat washer and injector placement: fit a new copper seat washer of the size used on the 6D125 injector seat, lower the injector vertically into the bore until it seats by hand, fit the hold-down clamp and finger-tighten the clamp bolt.
  3. Connector engagement: insert the high-pressure connector tube into the injector inlet seat and thread its retaining nut by hand until snug. Do not apply torque yet.
  4. Clamp alignment: pre-tighten the hold-down clamp bolt just enough to establish axial alignment in the bore, then final-tighten to the figure given in the Komatsu workshop manual for this engine.
  5. Connector nut: tighten the fuel connector retaining nut to the value stated in the Komatsu workshop manual for the 6D125.
  6. Fuel delivery pipe: connect the external high-pressure delivery pipe from the rail to the connector fitting and tighten both flare nuts to the manual figure.
  7. Calibration: read the injector calibration code before installation and program it into the ECM with the Komatsu diagnostic tool after fitting.
  8. Verification: start the engine, check for external fuel leaks at the connector and the clamp area, and confirm no cylinder-balance fault is reported.
Tips & Warnings:
  • Confirm the machine model and engine code from the serial-number plate before ordering; the same Denso family serves several Komatsu displacements and the injectors are not interchangeable.
  • Take the torque and washer figures from the Komatsu workshop manual for the specific machine, not from a listing or from another engine family.
  • Record the injector calibration code before installation and program it into the ECM afterwards.
06

Frequently Asked Questions

QWhich Komatsu machines and engine use Denso injector 095000-6070?

Denso 095000-6070 is the common rail injector for the Komatsu 6D125 six-cylinder industrial diesel engine (11.0 L), as fitted to PC400-8 and PC450-8 hydraulic excavators. The Komatsu genuine part number is 6251-11-3100.

QWhat genuine part number corresponds to Denso 095000-6070?

Komatsu genuine part number 6251-11-3100 (also written 6251113100). Denso aftermarket reference DCRI106070 is used for the same unit.

QWhat nozzle is fitted to 095000-6070?

The DLLA148P915 atomizing nozzle, Denso part number 093400-9150.

QIs 095000-6070 a Hino injector?

No. Hino 23670-series codes belong to different Denso injectors (for example 095000-6590 / 095000-6593 for the Hino J08E). 095000-6070 is a Komatsu 6D125 application and the two are not interchangeable.

QDoes replacing 095000-6070 require ECM coding?

Yes. The injector carries a calibration code that must be read from the new unit and programmed into the ECM. Record the code before installation; once the injector is seated, the marking may be difficult to read.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol