Catalog / DENSO / 095000-6593
DENSO

095000-6593

View Specs
SolenoidDenso Common Rail System (CRS)Euro 4

Denso Kobelco SK350 8 Injector 23670 E0520 Specs

Reference data for DENSO 095000-6593 common rail injector · OEM 095000-6590, 095000-6591, 095000-6592, 095000-6594, 095000-6595, 23670-E0520, VH23670E0520 · Application Hino J05E / J08E (5.1L / 7.7L)
OE REFERENCE095000-6590, 095000-6591, 095000-6592, 095000-6594, 095000-6595, 23670-E0520, VH23670E0520
CONTROL VALVEPLATE 10# / DENSO G2 VALVE PLATE
NOZZLEDLLA155P868
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The DENSO 095000-6593 is an authentic original-equipment G2 common rail diesel fuel injector engineered specifically for Hino J08E (6-cylinder, 7.7-liter, 197-209 kW / 264-280 hp) turbocharged electronically controlled diesel engines. Meeting EPA Tier 3 and EU Stage IIIA non-road industrial emissions standards, this injector is the primary combustion component deployed across Kobelco SK330-8, SK350-8, SK350LC-8, and SK380D-8 heavy hydraulic crawler excavators and Hino 500 Series Ranger heavy commercial trucks. Operating at rail pressures up to 1800 bar (26,100 psi) supplied by Denso HP3/HP4 high-pressure fuel pumps, this injector incorporates a calibrated DLLA155P868 multi-hole nozzle (Denso part number 093400-8680) and a hardened Plate 10# electro-hydraulic spool control valve to achieve precise micro-pilot, main, and split post-injection cycles. Denso part number 095000-6593 supersedes previous production revisions 095000-6590, 095000-6591, and 095000-6592, and corresponds directly to Hino OEM references 23670-E0520 and Kobelco construction machinery reference VH23670E0520.

Before You Order

CRITICAL WORKSHOP NOTICE: Always photograph or manually record the 30-digit Denso QR Compensation Code laser-etched onto the injector solenoid cap BEFORE installation. Once the injector is seated in the cylinder head, this calibration code cannot be read. Denso 095000-6593 (Hino OEM 23670-E0520 / Kobelco VH23670E0520) is the flagship electro-hydraulic G2 common rail injector powering Hino J08E (7.7L 6-cylinder) Tier 3 / Stage IIIA diesel engines in Kobelco SK330-8, SK350-8, and SK380D-8 hydraulic excavators. Tighten the injector hold-down clamp bolt to 30 N·m (22 lb·ft) and the high-pressure fuel feed line nut to 30 N·m (22 lb·ft). Writing the 30-digit QR code into the engine ECM via Hino DX, Hino e-Doctor, or Kobelco diagnostic software is mandatory to avoid severe idle vibration, cylinder contribution imbalances, and black smoke under hydraulic load. CAUTION: Never mix 095000-6593 with 095000-6353 (Hino 23670-E0050) as nozzle flow ratings and injection delivery maps differ significantly.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
Aftermarket
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Kobelco SK330-8 / SK330LC-8J05E / J08E2006-2016
Kobelco SK350-8 / SK350LC-8J05E / J08E2006-2016
Kobelco SK380D-8 Mining Crawler ExcavatorJ05E / J08E2007-2016
Hino 500 Series Ranger Heavy TruckJ05E / J08E2006-2016
Hino 700 Series Heavy Commercial TruckJ05E / J08E2006-2015
04

Technical Specifications

SpecificationValue
SKU095000-6593
BrandDENSO
TypeG2 Common Rail Fuel Injector
OE Number23670-E0520, VH23670E0520, 095000-6590
Injection SystemDenso Common Rail System (CRS ECD-U2 / G2)
Operating PressureCore Spec
Torque Spec30 N·m
Hold Down Torque30 N·m
Warranty12 Months
Emission StandardEPA Tier 3 / EU Stage IIIA
Engine FamilyHino J08E (7.7L 6-Cylinder)
Coding RequiredYes (Denso 30-Digit QR Compensation Code / Hino DX)
05

Installation Tips

Tools needed: Calibrated torque wrench (10-60 N·m range), Hino DX / Hino e-Doctor or Kobelco diagnostic scan tool with J2534 VCI, Denso QR code reader or high-resolution smartphone camera, Injector bore reamer and copper seat cleaning brush kit, Lint-free industrial cleaning swabs, Clean engine oil or assembly lubricant for O-rings, High-pressure fuel injection pipe socket (17 mm flare nut wrench), Compressed air line with rubber nozzle

  1. Clean Cylinder Head Bore and Ream Seat: Thoroughly clean the injector bore down to the bottom copper washer landing. Use an injector seat reamer to remove carbon glaze, varnish, and old washer debris. Blow out debris with dry compressed air while plugging the nozzle tip passage. Ensure the seating surface is 100% flat, clean, and dry.
  2. Install New Copper Sealing Washer and O-Rings: Fit a new genuine OEM copper washer (thickness ~1.5 mm) onto the injector nozzle body. Never reuse an old compressed washer. Lightly lubricate the upper body rubber O-ring with clean engine oil to prevent shearing or binding upon insertion into the rocker housing.
  3. Seat Injector and Tighten Clamp Bolt: Carefully lower the injector vertically into the cylinder head bore until the copper washer firmly contacts the cylinder head seat. Position the hold-down clamp fork centrally over the injector shoulder. Torque the clamp retaining bolt evenly to 30 N·m (22 lb·ft).
  4. Connect High-Pressure Rail Line and Solenoid Harness: Hand-thread the high-pressure fuel pipe union nuts onto the fuel rail and injector inlet fittings to guarantee cross-thread prevention. Final torque both line nuts to 30 N·m (22 lb·ft). Connect the two electrical solenoid terminals and torque retaining nuts gently to 2.5 N·m (22 lb·in).
  5. Bleed Fuel System and Program Denso 30-Digit QR Code: Connect the Hino DX or Kobelco diagnostic tool. Select Injector Calibration / Compensation Code Registration and input the 30-digit alphanumeric QR code recorded before installation for the specific cylinder. Prime the fuel system using the priming pump, start the engine, and perform an automated high-pressure rail leak test and cylinder cut-out test.
Tips & Warnings:
  • Before fitting 095000-6593, verify the listed engine and machine fitment against the EPC or workshop manual.
  • Keep the injector and fuel-system openings clean and capped until installation to prevent contamination.
  • Confirm the required torque and any adaptation procedure in the vehicle's workshop data rather than using generic values.
06

Frequently Asked Questions

QWill this injector fit my machine?

It is listed for the Hino engine family and Kobelco excavator applications covered by this product, and the correct unit is 095000-6593. Confirm your engine and model against the EPC or workshop data before ordering.

QWhat symptoms suggest the injector has failed?

Typical signs include rough running, misfire, poor power, excessive smoke, hard starting, or a fuel-system fault code. Confirm diagnosis with proper diesel common-rail testing before replacing parts.

QWhat should I check before ordering?

Verify the engine family, machine or truck model, and existing injector markings against the vehicle's EPC or workshop manual. Make sure the listed fitment matches and that 095000-6593 is the required unit.

QDoes the replacement need coding or adaptation?

Coding or adaptation requirements are not stated here, so confirm them against the vehicle's EPC or workshop manual. Do not assume the old unit can be reused or that seals can be reused without checking.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol