Catalog / DENSO / 095000-8340
DENSO

095000-8340

View Specs
SolenoidDenso Common Rail System (CRS)Euro 5

Denso Mitsubishi 4D56 HP Injector 1465A367 Data

Reference data for DENSO 095000-8340 common rail injector · OEM DCRI108340, 1465A367, 1465A367-T, 095000-8341 · Application Mitsubishi 4D56 HP (2.5L DI-D Common Rail)
OE REFERENCEDCRI108340, 1465A367, 1465A367-T, 095000-8341
CONTROL VALVEPLATE #29
NOZZLEG3S6 / DLLA147P1049
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Denso 095000-8340 (Mitsubishi OE part number 1465A367, aftermarket reference DCRI108340) is a third-generation (Denso G3) high-pressure electro-hydraulic common rail diesel injector developed specifically for the Mitsubishi 4D56 High Power (4D56 HP) 2.5-liter 16-valve DOHC intercooled turbo diesel engine. Fitted to Euro 5 specification Mitsubishi L200 / Triton pickups (KB4T/KA4T chassis) and Pajero Sport / Montero Sport SUVs producing 131 kW (178 hp) and 400 N·m of torque, this injector operates at an increased peak injection pressure of 2000 bar (200 MPa), up from the 1800 bar used in earlier Euro 4 models. Equipped with a modernized G3S6 micro-sac nozzle (093400-1049) and a high-speed hydraulic control valve Plate #29, the 095000-8340 delivers ultra-precise multi-injection shaping to satisfy Euro 5 particulate and NOx limits with a variable-geometry turbocharger (VGT). After mechanical installation with a hold-down clamp torque of 28 N·m, the laser-engraved 30-digit Denso QR compensation code on the electrical connector must be written into the engine ECM, followed by an automatic small injection quantity adaptation. > CRITICAL COMPATIBILITY WARNING: Do not interchange the Euro 5 High Power injector 095000-8340 (1465A367) with the earlier Euro 4 standard injector 095000-5600 / 1465A054. Although physically similar in exterior dimensions, internal hydraulic flow rates, nozzle tip spray angles (DLLA145P870 vs G3S6), and ECM timing calibrations differ substantially. Interchanging them causes severe combustion knock, black smoke under boost, and premature DPF clogging.

Before You Order

Always verify the OE reference DCRI108340, 1465A367, 1465A367T, 0950008341 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 095000-8340 needs its calibration code transferred after fitting; read the code from the new unit and program it with a compatible diagnostic tool.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Mitsubishi L200 / Triton / Pajero SportMitsubishi 4D56 HP (2.5L DI-D Common Rail)2009-2016
04

Technical Specifications

SpecificationValue
INJECTOR TYPECommon Rail Injector
SYSTEM PLATFORMCRI
CONTROL VALVECore Spec
NOZZLE CODECore Spec
OPERATING PRESSURECore Spec
05

Installation Tips

  1. Record QR Data: Note the 30-digit hexadecimal QR code printed on top of the solenoid connector before installing.
  2. Bore Preparation: Thoroughly ream and clean the injector sleeve in the cylinder head using a brass brush. Remove all baked carbon and vacuum clean.
  3. New Copper Washer: Always fit a brand-new 1.5 mm copper flame washer (ID 7.7 mm / OD 15.0 mm). Never reuse old washers.
  4. Injector Insertion: Apply a thin coating of clean engine oil to the body O-ring and lower the injector vertically into the bore until seated squarely.
  5. Clamp Torquing: Fit the hold-down fork and torque the retaining bolt to 28 N·m (21 lb·ft).
  6. High-Pressure Pipe: Hand-thread the fuel pipe flare nut, then torque to 32 N·m (24 lb·ft) using a 17 mm flare nut wrench.
  7. Fuel Leak-Off Rail: Install the spill rail with new aluminum seal rings and torque the banjo bolts to 14 N·m (10 lb·ft).
  8. ECU Programming: Connect Mitsubishi MUT-III or a compatible professional scanner (Launch, Autel, Bosch KTS). Enter Engine -> Special Functions -> Injector Identification Code Registration and enter the 30-digit code for each cylinder.
  9. Small Injection Quantity Learning: Warm the engine coolant above 80°C (176°F), switch off all electrical accessories, and execute the automated Small Injection Quantity Learning procedure to stabilize idle fueling.
Tips & Warnings:
  • Tighten the injector mounting/hold-down fasteners to 28 N·m.
  • Tighten the high-pressure line to 32 N·m.
  • Confirm the part number 095000-8340 and vehicle fitment against the EPC before installation.
06

Frequently Asked Questions

QWill this injector fit my Mitsubishi L200 / Triton / Pajero Sport?

This common-rail diesel injector, part number 095000-8340, has a listed system pressure of 2000 bar and is listed for the Mitsubishi 4D56 HP 2.5L DI-D Common Rail engine family in Mitsubishi L200 / Triton / Pajero Sport vehicles from 2009-2016. Check the vehicle's EPC for your exact application before ordering. The listed cross references are 0950008340, DCRI108340, 1465A367, 1465A367T, 0950008341, and 0950005471.

QWhat diagnostic trouble codes are associated with this injector?

The verified diagnostic trouble codes listed for this common-rail diesel injector are P0300, P0301, P0087, P0302, and P0304. Other failure symptoms or diagnostic criteria are not stated in the verified facts and must be confirmed against the vehicle's EPC instead of guessing.

QDoes this injector need coding or adaptation after installation?

The verified facts do not state coding or adaptation requirements for part 095000-8340. Confirm coding/adaptation requirements against the vehicle's EPC instead of guessing.

QHow can I verify the old injector before ordering a replacement?

Compare the old injector's markings with part number 095000-8340 and the listed cross references: 0950008340, DCRI108340, 1465A367, 1465A367T, 0950008341, and 0950005471. If the markings are unclear, confirm fitment against the vehicle's EPC instead of guessing.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol