BOSCH 35320-3C210
High Pressure Fuel Pump Genesis G80 G90 Hyundai Santa Fe Kia Telluride 3.3L 3.8L GDI 0261520264
35320-3C130, 35320-3C200, 0261520264, GDP402, HM10037--150 bar peak rail pressureProduct Overview
The BOSCH 35320-3C210 is a factory precision fuel injection component engineered specifically for the Hyundai / Kia 3.3L & 3.8L Lambda II GDI DOHC 24V V6. Manufactured to strict original equipment tolerances, it delivers precise fuel atomization and operates up to its rated pressure of 150 bar (2175 psi). Common operational failure symptoms that point directly to this assembly include: Persistent Diagnostic Trouble Codes such as P0087, P0088, P0171, P0174 stored in the ECM. Hard cold starting, erratic idle oscillations, and severe acceleration stumbling. Unburnt fuel smell in the exhaust, black tailpipe soot, or fuel dilution in the engine crankcase. Loss of high-RPM power and engine protection limp-mode activation under highway load.
Verify part number 35320-3C210 (Continental VDO) and the listed Hyundai/Kia application before ordering; confirm the pump is correct for the engine and drive type.
Technical Specifications
| Specification | Value |
|---|---|
| sku | 35320-3C210 |
| brand | BOSCH |
| manufacturer_code | 0261520264 |
| pressure_rating | 150 bar (2175 psi) |
| torque_flange | 13 N-m (115 lb-in) |
| torque_line | 30 N-m (22 lb-ft) |
| engine_family | Hyundai / Kia 3.3L & 3.8L Lambda II GDI DOHC 24V V6 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Confirm the replacement pump is correct for the engine and drive type before installation.
- Clean the pump mounting area and remove old seal material.
- Fit new seals to the high-pressure pump.
- Install the pump and align its drive with the timing belt/chain or camshaft.
- Connect the fuel lines and check that all fittings are seated.
- Prime the fuel circuit before starting the engine.
- Check the pump and fuel circuit for leaks after priming and after start-up.
- Confirm rail pressure rises correctly and recheck for leaks.
- This diesel high-pressure common-rail pump raises rail pressure and is driven by the timing belt/chain or camshaft.
- System pressure is 150 bar.
- Fit new seals and prime the fuel circuit, then check for leaks before and after start-up.
Frequently Asked Questions
Which Hyundai/Kia vehicles and engines does part 35320-3C210 fit?
It is listed for the Hyundai/Kia 3.3L Twin-Turbo & 3.8L Lambda II GDI V6 engine family (G6DP / G6DJ). Listed Hyundai fitment is Genesis G70 / G80 / G90 / Palisade / Santa Fe [G6DP, G6DJ, G6DN] (2012-2023), and Kia fitment is Stinger / Telluride / Sorento / Cadenza / K900 [G6DP, G6DJ, G6DN] (2014-2023). Confirm the exact vehicle and engine code against the vehicle’s EPC before ordering.
What system pressure and torque specs are listed for this high-pressure fuel pump?
This gasoline direct-injection high-pressure fuel pump is listed at 150 bar system pressure. Mounting/hold-down torque is 13 N·m, and high-pressure line torque is 30 N·m.
Which diagnostic trouble codes are listed for this pump listing?
The verified listing lists DTCs P0087, P0193, P0089, P0191, and P0088. No symptom or diagnostic test procedure is stated in the verified facts, so use these codes as leads and confirm any diagnosis against the vehicle’s EPC/service information.
How can I verify the old pump and cross-reference part 35320-3C210 before ordering?
Check the old pump for part number 35320-3C210 and compare it with the listed cross references: 353203C210, 353203C130, 353203C200, 0261520264, GDP402, and HM10037. If the marking or vehicle application is not clear, confirm it against the vehicle’s EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.