BOSCH A1770700200
Piezo Fuel Injector Mercedes C63 E63 S63 G63 AMG GT 4.0T V8 M177 M178 0261500424
1770700200, A1770706200, 0261500425, FJ1302, 0261500424--200 bar peak rail pressureProduct Overview
The A1770700200 is an original equipment (BOSCH) precision component engineered specifically for the Mercedes-AMG 4.0L BiTurbo Hot-V DOHC 32V V8 (M177 / M178). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0172.
Always verify the OE reference 1770700200, A1770706200, FJ1302 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. A1770700200 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Mercedes-Benz C-Class / E-Class / S-Class / GLC-Class / GLE-Class (W205/W213/W222) | M177 | 2015-2023 |
| Mercedes-Benz G-Class (W463A) / AMG GT (C190) | M177 / M178 | 2015-2024 |
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | A1770700200 |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | Mercedes-AMG 4.0L BiTurbo Hot-V DOHC 32V V8 (M177 / M178) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 14 N-m (10 lb-ft) |
| Fuel Line / Rail Torque | 25 N-m (18 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0172 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 14 N-m (10 lb-ft), and torque fuel line fittings to 25 N-m (18 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the vehicle’s engine family and EPC application before installing this gasoline direct-injection injector.
- Torque the mounting/hold-down fastener to 14 N·m.
- Torque the high-pressure line to 25 N·m.
Frequently Asked Questions
Will this injector fit my Mercedes-AMG M177/M178 vehicle?
This gasoline direct-injection injector, part number A1770700200, is listed for the Mercedes-AMG 4.0L BiTurbo Hot-V DOHC 32V V8 (M177/M178). Listed applications are C-Class/E-Class/S-Class/GLC-Class/GLE-Class (W205/W213/W222) with M177 (2015-2023), and G-Class (W463A)/AMG GT (C190) with M177/M178 (2015-2024). Confirm the exact vehicle against its EPC before ordering.
What diagnostic trouble codes are listed for this injector?
The verified diagnostic trouble codes for this listing are P0300, P0301, P0087, P0302, and P0304. No separate symptom list is provided, so confirm the diagnosis against the vehicle’s EPC instead of guessing before replacement.
Does this injector require coding or adaptation after installation?
Coding or adaptation requirements are not stated in the verified facts. Confirm the required procedure for the specific vehicle against its EPC instead of guessing.
How can I verify the old injector part number?
Compare the old unit’s markings with part number A1770700200 and the listed cross references: A1770700200, 1770700200, A1770706200, 0261500425, FJ1302, 0261500424. If markings are unclear or differ, confirm fitment against the vehicle’s EPC before replacement.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.