Catalog / CONTINENTAL / A2710700501
CONTINENTAL

CONTINENTAL A2710700501

View Specs
SolenoidContinental / VDO Common RailEuro 6

High Pressure Fuel Pump Mercedes Benz C250 SLK250 E250 1.8L Turbo W204 W212 M271 EVO 5WK97000

Reference data for CONTINENTAL A2710700501 high-pressure fuel pump · OEM A2710700401, 2710700501, 2710700401, 5WK97000 · Application Mercedes-Benz M271 EVO (1.8L CGI Turbo M271.820 / M271.860)
OE REFERENCEA2710700401, 2710700501, 2710700401, 5WK97000
CONTROL VALVEINTEGRATED PULSE-WIDTH MODULATED QUANTITY CONTROL SOLENOID
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Continental A2710700501 (Mercedes-Benz OE reference A2710700401, alternate casting numbers 2710700501 and Continental engineering number 5WK97000) is the original equipment mechanical high-pressure fuel pump (HPFP) developed for Mercedes-Benz's turbocharged 1.8-liter M271 EVO four-cylinder CGI engines. Operating at fuel rail pressures up to 140 bar (2030 psi), this camshaft-driven pump delivers precise direct injection metering for high-population luxury vehicles including the Mercedes-Benz C250 (W204), SLK250 (R172), and E250 CGI (W212/C207). A well-documented point of vulnerability on the M271 EVO platform involves internal plunger seal and diaphragm failure within the pump body. When the internal barrier ruptures, pressurized gasoline leaks backwards past the pump shaft directly into the cylinder head valve cover and crankcase oil. Drivers observe severe engine oil dilution, a strong fuel smell on the oil dipstick, rising oil level, long morning cranking times, check engine lights, and diagnostic trouble code P0087 (Fuel Rail/System Pressure Too Low). Uncorrected dilution causes catastrophic timing chain and crankshaft bearing wear. Correct replacement demands rigorous workshop compliance. Technicians must inspect the camshaft driving cup, lubricate the new flange Viton O-ring with clean motor oil, and torque the mounting fasteners crosswise to 10 N·m (89 in-lb). The high-pressure steel delivery pipe union must be torqued to 25 N·m (18 lb-ft). If crankcase gasoline dilution is present, an immediate engine oil and filter flush is mandatory prior to engine startup.

Before You Order

Always verify the OE reference A2710700401, 2710700501, 2710700401, 5WK97000 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. A2710700501 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Mercedes-Benz C250 CGI W204Mercedes-Benz M271 EVO (1.8L CGI Turbo M271.820 / M271.860)2012-2015
Mercedes-Benz SLK250 R172Mercedes-Benz M271 EVO (1.8L CGI Turbo M271.820 / M271.860)2012-2016
Mercedes-Benz E250 CGI W212Mercedes-Benz M271 EVO (1.8L CGI Turbo M271.820 / M271.860)2009-2016
04

Technical Specifications

SpecificationValue
System TypeMercedes-Benz CGI 140-bar High-Pressure Direct Injection System
Operating PressureCore Spec
Drive InterfaceExhaust Camshaft Driven Multi-Lobe Mechanical Plunger Interface
Mounting Bolt Torque10 N·m (89 in-lb) Torx E10 fasteners
High-Pressure Line Flare Nut25 N·m (18 lb-ft) steel fuel delivery line union
Internal Seal ArchitectureMulti-Lip Reinforced Fuel Plunger Barrier Diaphragm
ManufacturerCONTINENTAL
Continental Production Number5WK97000
05

Installation Tips

  1. Low-Pressure Fuel Rail Pressure Depressurization: Disconnect fuel pump control module fuse in rear SAM trunk module. Crank engine for 5 seconds to bleed system, then disconnect negative battery lead.
  2. Air Filter Housing & Noise Insulation Shield Removal: Unclip air intake ducting, remove air cleaner assembly, and detach heat-shielding foam blanket encapsulating the rear cylinder head HPFP.
  3. High-Pressure Steel Rail Feed Pipe Disconnection: Counter-hold pump discharge union with a 19mm open-end wrench while loosening 17mm flare nut on rigid steel pipe leading to the direct injection fuel rail.
  4. HPFP Fasteners Removal & Drive Cup Inspection: Remove mounting Torx bolts gradually to release internal spring pre-load. Extract pump and inspect camshaft follower driving cup and spring assembly for galling.
  5. New Pump Installation & Torque Sequence: Lubricate new Viton O-ring with clean synthetic engine oil. Seat pump flush against cylinder head flange, torque mounting bolts to 10 N·m (89 in-lb) and high-pressure pipe nut to 25 N·m (18 lb-ft).
Tips & Warnings:
  • Inspect engine oil immediately for fuel dilution: Internal diaphragm leakage allows unburnt gasoline into the cylinder head, diluting oil, raising dipstick level, and ruining rod bearings.
  • Always change engine oil and filter: If fuel odor is detected on the dipstick or P0087 was stored, perform an immediate complete engine oil and filter service.
  • Counter-hold pump outlet fitting: Never torque high-pressure flare line without securing the pump housing fitting with a counter-holding wrench.
  • Prime fuel circuit prior to ignition: Switch ignition ON for 10 seconds without starting to prime low-pressure feed and purge air pockets from the pump.
06

Frequently Asked Questions

QWill this high-pressure pump fit my Mercedes-Benz?

This diesel common-rail high-pressure pump is listed for the Mercedes-Benz C-Class, SLK, and E-Class applications shown for A2710700501. Confirm fitment against your VIN and the vehicle EPC before ordering.

QWhat symptoms suggest the pump has failed?

Look for hard starting, crank/no-start, poor power, rough running, fuel leaks, or rail-pressure faults. Diagnose first, since these symptoms can also come from other diesel common-rail faults.

QWhat should I check before ordering this pump?

Verify the part number A2710700501, confirm the application by VIN/EPC, inspect for contamination or metal debris, and check the workshop data for required coding or adaptation.

QDoes the replacement pump need coding or adaptation?

Coding, adaptation, and matching requirements are not stated here. Confirm them against the vehicle EPC or workshop manual, and follow the manufacturer's diagnostic procedure after installation.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol