BOSCH A2760700587
Piezo Fuel Injector Mercedes C43 AMG E400 S400 ML350 GLE400 3.0T 3.5L V6 M276 0261500067
A2760700187, 2760700587, 0261500068, FJ1212, 0261500067--200 bar peak rail pressureProduct Overview
The A2760700587 is an original equipment (BOSCH) precision component engineered specifically for the Mercedes-Benz 3.0L & 3.5L BiTurbo BlueDIRECT DOHC 24V V6 (M276 DE30 / DE35). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0172.
Always verify the OE reference A2760700187, 2760700587, FJ1212 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. A2760700587 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Mercedes-Benz C43 AMG W205 | M276 | 2016-2021 |
| Mercedes-Benz E-Class (W213) | M276 | 2016-2020 |
| Mercedes-Benz GLE43 AMG W166 | M276 | 2016-2019 |
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | A2760700587 |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | Mercedes-Benz 3.0L & 3.5L BiTurbo BlueDIRECT DOHC 24V V6 (M276 DE30 / DE35) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 14 N-m (10 lb-ft) |
| Fuel Line / Rail Torque | 23 N-m (17 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0172 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 14 N-m (10 lb-ft), and torque fuel line fittings to 23 N-m (17 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the part number A2760700587 and listed cross references against the vehicle's EPC before ordering.
- Tighten the injector mounting/hold-down to 14 N·m and the high-pressure line to 23 N·m as listed.
- Check the listed diagnostic trouble codes P0300, P0301, P0087, P0302, and P0304 when diagnosing a suspected injector issue.
Frequently Asked Questions
Will this A2760700587 gasoline direct-injection injector fit my Mercedes-Benz C43 AMG W205?
It is listed for the Mercedes-Benz C43 AMG W205 with M276 engine (2016-2021), E-Class W213 with M276 (2016-2020), and GLE43 AMG W166 with M276 (2016-2019). Confirm your VIN and engine against the vehicle's EPC before ordering.
What symptoms or fault codes are associated with a suspected failed injector for this M276 application?
The provided facts do not list symptoms, but the listing lists diagnostic trouble codes P0300, P0301, P0087, P0302, and P0304. Confirm the diagnosis and part fitment against the vehicle's EPC before replacing the injector.
Does this injector require coding or adaptation after installation?
The provided facts do not state coding or adaptation requirements for this gasoline direct-injection injector. Confirm any coding or adaptation requirement against the vehicle's EPC instead of guessing.
Can I reuse the seals or hold-down hardware when replacing this injector?
The provided facts do not state seal or hold-down reuse guidance. They do state a mounting/hold-down torque of 14 N·m and a high-pressure line torque of 23 N·m, so confirm seal reuse and any additional parts against the vehicle's EPC before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.