BOSCH 9A211012800
DFI Fuel Injector Porsche 911 991.2 Carrera S GTS 718 Cayman 3.0T 2.5T 0261500405
9A211012801, 0261500405--200 bar peak rail pressureProduct Overview
The 9A211012800 is an original equipment (BOSCH) precision component engineered specifically for the Porsche 3.0L Twin-Turbo Flat-6 & 2.5L Flat-4 DFI DOHC 24V (9A2 / MDD.DC / MDC.JA). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0172.
Always verify the OE reference 9A211012801 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 9A211012800 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 9A211012800 |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | Porsche 3.0L Twin-Turbo Flat-6 & 2.5L Flat-4 DFI DOHC 24V (9A2 / MDD.DC / MDC.JA) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 23 N-m (17 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0172 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 23 N-m (17 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Before fitting, verify that part number 9A211012800 matches the EPC listing for the vehicle.
- Follow the vehicle workshop manual for installation and post-repair checks; do not assume seal or coding requirements from the listing alone.
- Keep the injector protected until installation and confirm any adaptation steps in the workshop manual.
Frequently Asked Questions
Will part 9A211012800 fit my Porsche?
It is listed for the Porsche applications shown in the fitment data, including Boxster/Cayman and the applicable coupe applications. Confirm exact fitment by VIN or EPC before ordering.
What symptoms suggest this direct-injection injector has failed?
The provided data does not list failure symptoms; have the vehicle scanned and follow the workshop manual's diagnostic flow before replacing this injector.
What should I check before ordering this injector?
Confirm the part number 9A211012800 against the vehicle's EPC, verify the engine family and application in the fitment data, and check coding or seal requirements in the workshop manual.
Does the replacement injector need coding or adaptation?
Coding or adaptation requirements are not stated in the product data; confirm them against the vehicle's EPC or workshop manual before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.