HITACHI 16625AA040
High Pressure Fuel Pump Subaru WRX Forester XT Ascent 2.0T 2.4T FA20F FA24F
16625AA000, HUP0044INTEGRATED HIGH-SPEED FLOW CONTROL SPILL VALVE-200 bar peak rail pressureProduct Overview
The Hitachi 16625AA040 is a cam-driven single-plunger mechanical high-pressure fuel pump for Subaru and Toyota 2.0L / 2.4L boxer DIT engines (FA20F / FA24F). It is listed for the Subaru WRX VA (2015-2021), Forester XT SJ (2014-2018) and Ascent WN (2019-2024). The horizontal-opposed exhaust camshaft drive lobe actuates a roller tappet to a 200 bar (20 MPa / 2900 psi) injection pressure, with a proportional metering solenoid measuring 8.8-10.8 Ω at 20°C. Flanged retaining screws are torqued alternately to 12 N·m and the rigid flared delivery pipe fitting to 27 N·m. Common codes are P0087, P0088 and P0090. The internal drive plunger and roller bucket contact surface should be lubricated with clean motor oil.
Always verify the OE reference 16625AA000, HUP0044 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 16625AA040 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Subaru WRX VA | Subaru / Toyota 2.0L & 2.4L Boxer DIT / D-4S (FA20D / FA20F / FA24D / FA24F) | 2015-2021 |
| Subaru Forester XT SJ | Subaru / Toyota 2.0L & 2.4L Boxer DIT / D-4S (FA20D / FA20F / FA24D / FA24F) | 2014-2018 |
| Subaru Ascent WN | Subaru / Toyota 2.0L & 2.4L Boxer DIT / D-4S (FA20D / FA20F / FA24D / FA24F) | 2019-2024 |
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Hitachi Cam-Driven Single-Plunger Mechanical High-Pressure Fuel Pump |
| Operating PressureCore Spec | |
| Drive Configuration | Horizontal-opposed boxer exhaust camshaft drive lobe with roller tappet |
| Flange Mounting Bolt Torque | 12 N·m (flanged retaining screws torqued alternately) |
| High Pressure Line Torque | 27 N·m (rigid flared delivery pipe fitting) |
| Flow Regulator Valve Resistance | 8.8 - 10.8 Ω at 20°C (proportional metering solenoid) |
| Common Fault Codes | P0087 (Fuel Rail Pressure Low), P0088 (Rail Pressure High), P0090 (Fuel Pressure Regulator Control) |
| Workshop Precaution | Lubricate internal drive plunger and roller bucket contact surface with clean motor oil |
Installation Tips
- Relieve Direct Injection Pressure & Disconnect Battery: Depressurize fuel line via scan tool command or fuel pump relay removal. Disconnect negative battery ground.
- Remove Intercooler Piping & Foam Sound Damper: Remove upper charge air piping on passenger side of engine bay. Unclip protective foam sound insulation around HPFP.
- Disconnect Fuel Unions & Mounting Flange Fasteners: Unplug electrical harness from flow control solenoid. Disconnect high-pressure pipe (27 N·m). Back out two flange bolts evenly to release spring tension.
- Reinstall Replacement Pump, Torque Bolts & Test Pressure: Fit new lubricated O-ring seal. Torque mounting flange bolts alternately to 12 N·m. Tighten delivery line to 27 N·m. Crank engine and verify fuel rail pressure.
- Before fitting 16625AA040, confirm the vehicle EPC listing and inspect the fuel system for contamination.
- Use the vehicle workshop manual for all tightening, coding, and adaptation procedures because those details are not stated here.
- Do not reuse seals or assume compatibility unless the workshop manual and EPC confirm it for this pump.
Frequently Asked Questions
Will 16625AA040 fit my Subaru?
It is listed for the WRX VA, Forester XT SJ, and Ascent WN fitments shown; confirm your exact engine variant and VIN against the vehicle EPC before ordering.
What are the symptoms of a failed high-pressure common-rail pump?
Exact failure symptoms are not stated here; confirm them against the vehicle workshop manual and diagnose the common-rail system for fuel delivery and contamination before replacing 16625AA040.
What should I check before ordering 16625AA040?
Confirm the vehicle EPC listing, engine variant, and that the existing pump has not contaminated the fuel system; verify any coding or adaptation requirements in the workshop manual before fitting.
Does the replacement pump need to be matched or adapted?
Adaptation or coding requirements are not stated for 16625AA040; confirm them against the vehicle EPC or workshop manual, and do not assume the old unit can be reused without checks.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.