DENSO 23100-24010
High Pressure Fuel Pump Toyota Tundra Land Cruiser 300 Sequoia Lexus LX600 3.5T V35A FTS
23100-24011, 297500-0320, 297500-0321, GDP202--200 bar peak rail pressureProduct Overview
The 23100-24010 is an original equipment (DENSO) precision component engineered specifically for the Toyota-Lexus 3.5L Twin-Turbo V6 D-4ST DOHC 24V (V35A-FTS). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P1604.
Always verify the OE reference 2310024011, 2975000320, 2975000321, GDP202 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 23100-24010 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 23100-24010 |
| Manufacturer Brand | DENSO |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Toyota-Lexus 3.5L Twin-Turbo V6 D-4ST DOHC 24V (V35A-FTS) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 21 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P1604 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 21 N-m (15 lb-ft), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Before removal, confirm 23100-24010 against the vehicle's EPC so the correct pump is fitted.
- Keep fuel and high-pressure line openings capped and work cleanly to prevent contamination.
- After installation, confirm any matching steps and torque values against the vehicle's workshop manual.
Frequently Asked Questions
Which vehicles is part 23100-24010 listed for?
23100-24010 is listed for Toyota Tundra, Sequoia, Land Cruiser, and Lexus LS, LX, and GX applications using the specified twin-turbo gasoline direct-injection engine family; confirm exact fitment in the EPC before ordering.
What symptoms should I expect from a failed pump?
The listing does not describe failure symptoms for 23100-24010; diagnose the vehicle with workshop data and confirm the high-pressure fuel pump is the cause before replacing it.
What should I check before ordering this pump?
Confirm the vehicle uses the listed twin-turbo gasoline direct-injection engine family, verify the model application in the EPC, and ensure the required pump part number is 23100-24010.
Does the replacement pump need matching or adaptation?
The listing does not state coding or adaptation requirements for 23100-24010; confirm whether matching is needed against the vehicle's EPC or workshop manual before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.