DENSO 23209-28080
Multi Point Fuel Injector Toyota Camry RAV4 Highlander Corolla Scion 2.4L 2AZ FE 23250 28080 FJ784
23250-28080, 23209-0H050, 23209-0H060, FJ784, 842-12304--3 bar peak rail pressureProduct Overview
The DENSO 23209-28080 is a precision automotive OE replacement component engineered specifically for Toyota 2.4L 16V DOHC VVT-i 2AZ-FE powertrains. Designed to deliver consistent calibration and factory-specified fuel atomization, this unit restores original throttle response, diagnostic rail pressure stability, and emission compliance.
Always verify the OE reference 2325028080, 232090H050, 232090H060, FJ784 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 23209-28080 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| part_number | 23209-28080 |
| oem_reference | 23209-28080 |
| manufacturer | DENSO |
| system_type | Fuel Injector |
| pressure_rating | 3.2 bar (46.4 psi) |
| operating_temperature | -40°C to +135°C |
| flange_mount_torque | 19 N-m (14 lb-ft) |
| high_pressure_line_torque | 19 N-m (14 lb-ft) |
| diagnostic_dtc | P0171, P0300, P0301, P0174 |
Installation Tips
- Depressurize the fuel system completely via diagnostic scan tool or by removing the fuel pump fuse prior to line disassembly.
- Clean all surrounding bracket areas thoroughly using residue-free brake cleaner to prevent abrasive particulate ingress.
- Inspect the mechanical camshaft lobe and roller follower or clean injector bore seating surfaces before hardware alignment.
- Install component using fresh factory O-rings or Teflon combustion chamber seals lubricated only with clean motor oil.
- Torque mounting flange fasteners in alternating increments to 19 N-m (14 lb-ft).
- Torque high-pressure hydraulic tube fittings using a calibrated flare nut wrench to 19 N-m (14 lb-ft).
- Prime low-pressure fuel circuit, cycle ignition key 3-4 times, and inspect for high-pressure hydraulic leaks before road test.
- Always replace single-use high-pressure metal fuel lines and micro-filter seals whenever disconnected.
- Verify camshaft driving lobe surfaces for scoring or flat spots before installing any mechanical pump.
- Reset long-term and short-term fuel trim adaptations via OBD-II diagnostic scanner after physical replacement.
Frequently Asked Questions
Will part number 23209-28080 fit my Toyota 2AZ-FE?
It is a multi-point (port) fuel injector listed for the Toyota 2.4L 16V DOHC VVT-i 2AZ-FE. Listed fitment is Toyota Camry (ACV30/ACV40), Solara, and Avalon (2002-2011), plus RAV4 (ACA20/ACA30), Highlander, Corolla, and Matrix (2004-2013). Confirm exact model, year, and engine against the vehicle EPC before ordering.
What installation torque and system pressure apply to this injector?
The mounting/hold-down torque is 19 N·m and the high-pressure line torque is 19 N·m; system pressure is 3 bar. If your vehicle-specific procedure is not covered by these facts, confirm it against the vehicle EPC/service information.
What fault codes or symptoms point to checking this port fuel injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. No specific failed-unit symptoms or test procedure are stated in the provided facts, so confirm diagnosis against the vehicle EPC/service information.
How can I verify the old injector before replacing it with 23209-28080?
Compare the old part against part number 23209-28080 and the listed cross references: 2320928080, 2325028080, 232090H050, 232090H060, FJ784, and 84212304. Confirm the exact vehicle application against the EPC; no resistance, flow, or dimension specifications are provided here.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.