HITACHI 079127025AF
High Pressure Fuel Pump Audi RS4 RS5 S6 S7 S8 A8 4.0T 4.2L V8 FSI HPP0017
079127025C, 0261520262, HPP0017--120 bar peak rail pressureProduct Overview
The 079127025AF is an original equipment (HITACHI) precision component engineered specifically for the Audi 4.0L TFSI & 4.2L FSI DOHC 32V V8 (EA824 / CEUC / CTGE / BNS). Operating at peak injection pressures up to 120 bar (1740 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference 079127025C, HPP0017 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 079127025AF needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 079127025AF |
| Manufacturer Brand | HITACHI |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Audi 4.0L TFSI & 4.2L FSI DOHC 32V V8 (EA824 / CEUC / CTGE / BNS) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 20 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 25 N-m (18 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (15 lb-ft), and torque fuel line fittings to 25 N-m (18 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the part number 079127025AF before installation.
- Torque the pump mounting/hold-down fasteners to 20 N·m.
- Torque the high-pressure line to 25 N·m.
Frequently Asked Questions
Will this 079127025AF pump fit Audi RS5 (B8) and Audi S6 (C7)?
The 079127025AF gasoline direct-injection high-pressure fuel pump is listed for Audi RS4 (B7) / RS5 (B8) / R8 BNS/CFSA (2006-2015). It is also listed for Audi S6 / S7 / RS6 / RS7 (C7) CEUC/CRDB (2012-2018) and Audi A8 / S8 (D4) CEUA/CTGA/DDTA (2012-2018), with engine family Audi 4.0L TFSI & 4.2L FSI DOHC 32V V8 (EA824 / CEUC / CTGE / BNS). For any fitment not covered by these listings, confirm against the vehicle's EPC.
What diagnostic trouble codes are listed for this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. The verified facts do not map these codes to specific symptoms, so confirm the diagnosis and part application against the vehicle's EPC instead of guessing.
What are the mounting/hold-down and high-pressure line torque specs, and what system pressure is listed?
The mounting / hold-down torque is 20 N·m, and the high-pressure line torque is 25 N·m. The listed system pressure is 120 bar.
How can I verify the old pump and what cross-reference numbers match 079127025AF?
The listing part number is 079127025AF, and the listed cross references are 079127025AF, 079127025C, 0261520262, HPP0017, and 0261520261. Compare these numbers with the old pump and confirm the vehicle application against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.