BOSCH 04E127025G
High Pressure Fuel Pump Volkswagen Golf 7 Jetta Passat Tiguan Audi A3 1.4 TSI EA211 0261520261
04E127025D, 0261520261, 0261520262, HPP0021, 04E127025BINTEGRATED FUEL METERING SOLENOID VALVE N290-200 bar peak rail pressureProduct Overview
The Bosch 04E127025G (0261520261) mechanical high-pressure fuel pump (HPFP) is the precision heart of the direct-injection fuel delivery system on Volkswagen Group's EA211 1.4 TSI/TFSI four-cylinder engine family. Operating at nominal system peak rail pressures up to 200 bar (2900 psi), this single-plunger pump is driven directly by a multi-lobe cam on the engine's camshaft via a roller follower tappet. Fuel delivery volume is modulated cycle-by-cycle through the pulse-width modulated N290 Fuel Metering Solenoid Valve, allowing the Bosch MED17 / ME17 engine control unit (ECU) to maintain closed-loop fuel rail pressure matching instantaneous boost and volumetric efficiency demands.
Always verify the OE reference 04E127025D, HPP0021 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 04E127025G needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Golf Mk7 / Jetta / Passat / Tiguan | Volkswagen / Audi EA211 1.4L & 1.5L TSI / TFSI (CZDA / CZEA / CHPA / DADA) | 2013-2020 |
| Audi A3 (8V) / Q3 (8U) | Volkswagen / Audi EA211 1.4L & 1.5L TSI / TFSI (CZDA / CZEA / CHPA / DADA) | 2013-2019 |
Technical Specifications
| Specification | Value |
|---|---|
| Operating PressureCore Spec | |
| Pump Technology | Single Plunger Mechanical Camshaft-Driven HPFP |
| Flow Control | Integrated Solenoid Fuel Metering Valve (N290) |
| Mounting Flange Torque | 20 N·m |
| High Pressure Line Torque | 27 N·m |
| Drive Type | Intake Camshaft Tri-Lobe Drive with Roller Tappet |
| Fuel Type | Gasoline / Premium Unleaded Direct Injection |
| OE Cross References | 04E127025G, 04E127025B, 04E127025D, 0261520261, 0261520262 |
| Failure Symptoms | Long crank on warm engine, P0087 low rail pressure, hesitation under load, limp mode |
| Diagnostic Test | Measure LPFP lift pressure (4-7 bar) vs HPFP peak rail pressure (140-200 bar) |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Disconnect 12V battery and relieve high-pressure fuel system residual pressure via scan tool or low-pressure port.
- Disconnect electrical connector from fuel metering valve N290 and unthread low-pressure feed hose.
- Counter-hold fitting and loosen high-pressure steel rail flare nut using a flare nut wrench.
- Evenly back out the two M6 mounting bolts half a turn at a time to prevent uneven spring tilting pressure.
- Inspect roller tappet in the cylinder head bore for scuffing, flat spotting, or excessive play; replace if worn.
- Lubricate new O-ring with clean motor oil, seat pump squarely, and torque mounting bolts alternately to 20 N·m.
- Hand-thread high-pressure line flare nut until seated, then torque precisely to 27 N·m; reconnect N290 plug.
- Cycle ignition to pressurize low-pressure circuit, verify zero fuel leaks around fittings, and clear stored DTCs.
- Confirm the vehicle’s engine family and fitment against the EPC before ordering.
- Tighten the pump hold-down to 20 N·m and the high-pressure line to 27 N·m.
- Match the old pump’s part number and listed cross references before replacement.
Frequently Asked Questions
Will this pump fit my Volkswagen Golf Mk7, Jetta, Passat, or Tiguan, or my Audi A3/Q3?
This 04E127025G gasoline direct-injection high-pressure fuel pump is listed for Volkswagen Golf Mk7 / Jetta / Passat / Tiguan (2013-2020) and Audi A3 (8V) / Q3 (8U) (2013-2019). It is also listed for the EA211 1.4L & 1.5L TSI / TFSI engine family (CZDA / CZEA / CHPA / DADA); confirm exact fitment against the vehicle’s EPC.
Which diagnostic trouble codes can point to a problem with this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. This pump is a 200 bar gasoline direct-injection high-pressure fuel pump; use the listed codes with proper diagnosis.
What are the mounting and high-pressure line torque values for this pump?
The mounting / hold-down torque is 20 N·m, and the high-pressure line torque is 27 N·m. Use these stated values for this 04E127025G pump.
Do I need coding or adaptation after installing this high-pressure fuel pump?
No coding or adaptation requirement is stated in the supplied facts for this 04E127025G pump. That must be confirmed against the vehicle’s EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.