CONTINENTAL 13537585261
Fuel Injector Index 12 BMW 335i 535i 135i X6 3.0T N54 Piezo Direct Injection
13537585261-12, 13537565138, 13537585261-11, FJ1055--200 bar peak rail pressureProduct Overview
The 13537585261 is an original equipment (SIEMENS VDO) precision component engineered specifically for the BMW 3.0L Twin-Turbo Inline-6 DOHC 24V (N54B30). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0302, P0171, P0172.
Always verify the OE reference 1353758526112, 13537565138, 1353758526111, FJ1055 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 13537585261 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 13537585261 |
| Manufacturer Brand | CONTINENTAL |
| Component Type | Direct Fuel Injector |
| Engine Application | BMW 3.0L Twin-Turbo Inline-6 DOHC 24V (N54B30) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 23 N-m (17 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0302, P0171, P0172 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 23 N-m (17 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm fitment against the vehicle's EPC using part number 13537585261 before installation.
- Tighten the injector hold-down to 13 N·m and the high-pressure line to 23 N·m.
- Verify the system pressure is 200 bar before diagnosing or servicing the injector.
Frequently Asked Questions
Will this injector fit my BMW?
It is listed for BMW 3 Series (E90/E92/E93) 3.0L Twin-Turbo N54B30 (2007-2010), BMW 1 Series (E82/E88) 3.0L Twin-Turbo N54B30 (2008-2010), BMW 5 Series (F10) 4.4L Twin-Turbo V8 N63B44 (2011-2013), and BMW 7 Series (F01/F02) 4.4L Twin-Turbo V8 N63B44 (2009-2012). Confirm fitment against the vehicle's EPC using part number 13537585261.
What diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. Any further symptom diagnosis must be confirmed against the vehicle's EPC instead of guessing.
Does this injector require coding or adaptation?
Coding or adaptation requirements are not stated in the supplied facts. Confirm the required procedure against the vehicle's EPC before installation.
Can I reuse the seals when installing this injector?
Seal reuse is not stated in the supplied facts. Confirm seal and hardware requirements against the vehicle's EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.