CONTINENTAL 13538616079
Piezo Direct Fuel Injector Index 12 BMW 135i 335i 535i 1M Z4 N54 550i 750i X5 N63 S63 13537585261
13537589048, 13537565137, FIJ0028--200 bar peak rail pressureProduct Overview
The VDO 13538616079 is a precision automotive OE replacement component engineered specifically for BMW 3.0L Twin-Turbo N54B30A & 4.4L V8 Twin-Turbo N63B44A / S63 powertrains. Designed to deliver consistent calibration and factory-specified fuel atomization, this unit restores original throttle response, diagnostic rail pressure stability, and emission compliance.
Always verify the OE reference 13537589048, 13537565137, FIJ0028 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 13538616079 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| part_number | 13538616079 |
| oem_reference | 13538616079 |
| manufacturer | CONTINENTAL |
| system_type | Fuel Injector |
| pressure_rating | 200 bar (2900 psi) |
| operating_temperature | -40°C to +135°C |
| flange_mount_torque | 13 N-m (9.5 lb-ft) |
| high_pressure_line_torque | 23 N-m (17 lb-ft) |
| diagnostic_dtc | P0300, P0301, P0302, P0172 |
Installation Tips
- Depressurize the fuel system completely via diagnostic scan tool or by removing the fuel pump fuse prior to line disassembly.
- Clean all surrounding bracket areas thoroughly using residue-free brake cleaner to prevent abrasive particulate ingress.
- Inspect the mechanical camshaft lobe and roller follower or clean injector bore seating surfaces before hardware alignment.
- Install component using fresh factory O-rings or Teflon combustion chamber seals lubricated only with clean motor oil.
- Torque mounting flange fasteners in alternating increments to 13 N-m (9.5 lb-ft).
- Torque high-pressure hydraulic tube fittings using a calibrated flare nut wrench to 23 N-m (17 lb-ft).
- Prime low-pressure fuel circuit, cycle ignition key 3-4 times, and inspect for high-pressure hydraulic leaks before road test.
- Always replace single-use high-pressure metal fuel lines and micro-filter seals whenever disconnected.
- Verify camshaft driving lobe surfaces for scoring or flat spots before installing any mechanical pump.
- Reset long-term and short-term fuel trim adaptations via OBD-II diagnostic scanner after physical replacement.
Frequently Asked Questions
Will part 13538616079 fit my BMW?
Part 13538616079 is listed for BMW 3 Series (E90/E92/E93) 3.0L Twin-Turbo N54B30 (2007-2010), BMW 1 Series (E82/E88) 3.0L Twin-Turbo N54B30 (2008-2010), BMW 5 Series (F10) 4.4L Twin-Turbo V8 N63B44 (2011-2013), and BMW 7 Series (F01/F02) 4.4L Twin-Turbo V8 N63B44 (2009-2012). Confirm fitment against the vehicle’s EPC using the part number.
What diagnostic trouble codes are listed for this injector?
The diagnostic trouble codes listed for this injector are P0300, P0301, P0087, P0302, and P0304. Use these codes for diagnosis, then confirm the injector part number and fitment against the vehicle’s EPC.
What are the mounting and high-pressure line torque specs for this injector?
The mounting/hold-down torque is 13 N·m, and the high-pressure line torque is 23 N·m. The listed system pressure for this gasoline direct-injection injector is 200 bar.
How can I verify the old injector and check cross references?
The part number is 13538616079, and the listed cross references are 13537589048, 13537565137, FIJ0028, 13537585261, and 13647597870. To verify the old part, confirm these references and the vehicle fitment against the vehicle’s EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.