Catalog / BOSCH / 0261500055
BOSCH

BOSCH 0261500055

View Specs
SolenoidGasoline Direct Injection (GDI / HDEV)Euro 5

High Pressure GDI Fuel Injector VW Audi 2.0 TFSI EA113 Golf R S3

Reference data for BOSCH 0261500055 common rail injector · OEM 06F906036A, 06F906036F, 06F906036G · Application Volkswagen / Audi EA113 2.0L TFSI (BPY / AXX / BWA / CDL)
OE REFERENCE06F906036A, 06F906036F, 06F906036G
CONTROL VALVEPRECISION SOLENOID ARMATURE WITH MULTI-HOLE ATOMIZER NOZZLE
NOZZLE-
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

The Bosch 0261500055 (VW/Audi OE 06F906036F / 06F906036G) is the genuine original equipment high-flow direct fuel injector for VAG 2.0 TFSI EA113 performance engines equipped with BorgWarner K04 turbochargers. Standard factory equipment on the Volkswagen Golf R (MK6), Audi S3 (8P), Audi TTS, and SEAT Leon Cupra R, this multi-hole solenoid injector delivers high-pressure atomization up to 130 bar. Typical failure symptoms include cold-start stumbling, black smoke on kickdown, and cylinder misfire codes P0300 through P0304.

Before You Order

COLD START CYLINDER WASH & INJECTOR TIP WEEPING: On performance EA113 2.0 TFSI engines (Golf R, S3, Cupra R), direct fuel injectors operate under continuous 130 bar rail pressure. Varnish buildup causes the injector needle to stick weeping open overnight. This floods the combustion chamber with raw gasoline, washing cylinder bore oil (Cylinder Wash), causing violent morning cold misfires (P0300, P0301), and damaging the catalytic converter. Always install a fresh Teflon combustion seal ring using a cone installation tool.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Volkswagen Golf R MK6BPY / AXX / BWA / CDL2010-2013
Audi S3 8PBPY / AXX / BWA / CDL2006-2012
Audi TTS 8JBPY / AXX / BWA / CDL2008-2014
04

Technical Specifications

SpecificationValue
Injector GenerationBosch HDEV-1 High-Pressure Gasoline Direct Injector
Operating Rail PressureCore Spec
Spray PatternHigh-Flow Multi-Hole Precision Atomizer Nozzle
Coil Resistance1.40 to 1.80 Ohms at 20°C
Combustion Seal TypeCombustion Chamber Virgin Teflon (PTFE) Ring
Special Assembly ToolVW/Audi T10133 Teflon Seal Expanding Cone & Sizing Sleeve
Fuel Rail Hold Down Torque10 N·m (Even cross-pattern)
Tightening Torque10 N·m
Hold Down Torque10 N·m
Primary OEM Reference06F906036A, 06F906036F, 06F906036G
Engine Emission ComplianceEuro 5 / Tier 2 Bin 5
Standard Industrial Warranty12 Months / Unlimited Mileage

Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)

Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.

BOSCHExact Engine & Chassis Match
06F127025K
Gasoline Direct Injection (GDI) • 120 bar
🚙 Engine Code AXX
Technical Specifications & Pinout
05

Installation Tips

Tools needed: VW/Audi T10133 Teflon seal installation guide cone and sizing sleeves, Slide hammer injector removal adapter T10133/1, Torque wrench calibrated for 8-15 N·m, Brass bore cleaning brush and lint-free cotton swabs, Clean engine oil or assembly lube for Viton rail O-rings

  1. Disconnect battery negative terminal; relieve low-pressure fuel circuit pressure before intake disassembly.
  2. Remove intake manifold to gain full access to high-pressure fuel rail and cylinder head injector ports.
  3. Disconnect electrical wiring harness connectors from all four GDI injectors.
  4. Remove fuel rail retaining bolts; extract fuel rail assembly evenly to prevent cocking injectors.
  5. Attach slide hammer puller T10133/1 to injector body; extract injector straight out of cylinder head bore.
  6. Clean carbon soot from injector cylinder head bore using brass brush and vacuum; never use steel tools.
  7. Remove old Teflon seal; expand new virgin Teflon ring over guide cone into injector seal groove.
  8. Slide sizing sleeve over Teflon ring and allow 5 minutes for Teflon memory recovery to shrink seal to diameter.
  9. Lubricate Viton upper O-ring with clean motor oil; insert injector into cylinder head bore by hand pressure.
  10. Reinstall fuel rail assembly; torque rail hold-down bolts evenly in stages to 10 N·m.
  11. Reinstall intake manifold with fresh gaskets; reconnect fuel lines and wiring connectors.
  12. Cycle ignition 3 times to prime system; start engine and inspect for fuel mist or combustion blow-by.
Tips & Warnings:
  • Teflon Seal Resizing Mandate: Never stretch Teflon seals with fingers; always use the T10133 cone and sizing sleeve to prevent combustion blow-by.
  • Bore Carbon Cleaning: Thoroughly clean injector bore carbon deposits before installing new injectors; carbon debris prevents proper seal seating.
  • Even Rail Torquing: Torque fuel rail retaining bolts evenly in cross-pattern to prevent side-loading injector bodies.
06

Frequently Asked Questions

QWhat is the difference between standard EA113 2.0T injectors and 0261500055 K04 injectors?

The 0261500055 (06F906036F) injector features a specialized high-flow multi-hole nozzle tip specifically calibrated for K04-turbocharged engines (Golf R, Audi S3). It delivers significantly higher volumetric flow than standard K03 GTI injectors (06F906036A) to support 265-270 hp output.

QCan leaking 0261500055 injectors cause cold misfires and oil fuel smell?

Yes. A worn or carbon-fouled direct injector that leaks overnight dumps unburned liquid fuel directly on the piston crown. This wets the spark plug causing a P0301-P0304 cold misfire and washes cylinder wall oil down into the crankcase.

QIs a special tool required to install the Teflon combustion chamber seal ring?

Yes, absolutely. The virgin Teflon combustion seal ring must be expanded over a guide cone onto the injector groove, then resized using a calibration compression sleeve. Never stretch the Teflon ring with bare fingers, or it will fail to seal, causing compression blow-by.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
DIESEL WORKSHOP DIAGNOSTIC SOP

Cylinder Balance & Injector Deviation Guide

Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol