BOSCH 06F127025K
High Pressure Fuel Pump VW Golf GTI Mk5 Jetta Passat Audi A4 B7 TT 2.0 TFSI EA113 0261520038
06F127025M, 06F127025J, 06F127025H, 06F127025F, 06F127025B, 261520038, 0261520044, HPP0004, 0261520038INTEGRATED HIGH-SPEED DIGITAL FLOW CONTROL SOLENOID (N276)-120 bar peak rail pressureProduct Overview
The Bosch 06F127025K (Bosch reference 0261520038, superseding part numbers 06F127025M, 06F127025J, and 06F127025F) is the benchmark mechanical high-pressure fuel pump (HPFP) engineered for Volkswagen and Audi's historic 2.0-liter EA113 turbocharged FSI/TFSI engines. Delivering operating fuel rail pressures up to 120 bar (1740 psi), this camshaft-actuated single-plunger pump meters fuel across prominent performance applications including the VW Golf Mk5 GTI, Jetta GLI, Passat B6, Audi A4 (B7), Audi A3 (8P), and Audi TT (8J). The primary vulnerability of the EA113 fuel system centers on the flat cam follower tappet positioned between the intake camshaft driving tri-lobe and the pump plunger shaft. Over time, friction depletes the diamond-like carbon (DLC) protective layer. Once breached, the camshaft lobe rubs directly against the pump plunger, destroying both components and generating diagnostic trouble code P0087 (Fuel Rail/System Pressure Too Low), severe acceleration cuts, and EPC limp-mode warnings. Metal shavings from worn followers can additionally circulate through the engine oil gallery. Precision installation demands strict adherence to factory procedures. Technicians must inspect the camshaft tri-lobe for surface scoring and insert a brand-new lubricated cam follower bucket. Flange mounting bolts must be drawn down evenly and torqued to 10 N·m (89 in-lb), while the high-pressure flared fuel line nut requires 27 N·m (20 lb-ft). High-pressure testing must verify leak-free operation at idle and wide-open throttle.
Always verify the OE reference 06F127025M, 06F127025J, 06F127025H, 06F127025F stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 06F127025K needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Golf Mk5 / Jetta | Volkswagen / Audi EA113 2.0L TFSI (BPY / AXX / BWA / CDL) | 2005-2008 |
| Audi A4 (B7) / A3 (8P) | Volkswagen / Audi EA113 2.0L TFSI (BPY / AXX / BWA / CDL) | 2005-2008 |
| Audi TT 8J | Volkswagen / Audi EA113 2.0L TFSI (BPY / AXX / BWA / CDL) | 2007-2014 |
Technical Specifications
| Specification | Value |
|---|---|
| System Type | VAG EA113 Bosch HDP 120-bar High-Pressure Direct Fuel Injection |
| Operating PressureCore Spec | |
| Pump Mechanism | Intake Camshaft Driven Single-Piston Plunger Pump |
| Mounting Flange Bolt Torque | 10 N·m (89 in-lb) M6 triple-square / Torx bolts |
| High-Pressure Line Nut Torque | 27 N·m (20 lb-ft) rigid steel delivery pipe flare nut |
| Low-Pressure Union Torque | 15 N·m (11 lb-ft) threaded brass inlet fitting |
| Cam Follower Interface | DLC Flat Tappet Bucket (requires mandatory inspection/replacement) |
| Manufacturer | Bosch (Tier-1 OEM for Volkswagen AG) |
| Bosch Production Number | 0261520038 / 0261520044 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Low-Pressure System Depressurization & Battery Disconnect: Pull low-pressure electric fuel pump fuse (Fuse 27 or 28) from fuse panel. Crank engine until it stalls to deplete line pressure, then disconnect negative battery terminal.
- Schrader Valve Residual Pressure Relief & Line Removal: Wrap rag around pump Schrader test valve (on banjo-bolt style) or loosen brass test port to relieve residual 50-bar rail pressure. Disconnect low-pressure rubber hose.
- High-Pressure Steel Flare Line Disconnection: Counter-hold the pump outlet adapter with a 19mm wrench while loosening the 17mm steel flare nut on the bottom high-pressure line. Thread nut back carefully.
- Mounting Fasteners Removal & Cam Follower Tappet Extraction: Remove three M6 mounting bolts evenly in half-turn steps against internal spring force. Slide pump out and immediately extract the flat cam follower tappet with a magnet.
- Camshaft Lobe Inspection, Follower Replacement & Torque: Inspect intake camshaft drive tri-lobe for scoring. Coat brand-new DLC cam follower with fresh engine oil. Install new Viton O-ring, torque mounting bolts evenly to 10 N·m (89 in-lb) and metal line flare nut to 27 N·m (20 lb-ft).
- Mandatory cam follower inspection: The flat bucket tappet wears through its black DLC coating; a perforated follower will grind the camshaft lobe flat, requiring camshaft replacement.
- Always replace the internal Viton sealing O-ring: Reusing the square-cut or round flange O-ring will result in oil weeping down the cylinder head timing chain housing.
- Counter-hold pump outlet fitting: Failing to support the hex adapter on the HPFP body when torquing the flare nut will crack the internal threaded aluminum boss.
- Prime before starting: Turn ignition key ON for 5 seconds three times without cranking to prime the low-pressure circuit and bleed air from the pump chamber.
Frequently Asked Questions
Will part number 06F127025K fit my Volkswagen or Audi?
It is listed for the Volkswagen/Audi EA113 2.0L TFSI engine family (BPY, AXX, BWA, CDL) in Golf Mk5/Jetta 2005-2008, Audi A4 B7/A3 8P 2005-2008, and Audi TT 8J 2007-2014. Cross references are 06F127025K, 06F127025M, 06F127025J, 06F127025H, 06F127025F, and 06F127025B. If your exact vehicle is not covered by that list, confirm fitment against the vehicle’s EPC.
What are the mounting and high-pressure line torque specs for this pump?
The mounting/hold-down torque is 10 N·m. The high-pressure line torque is 27 N·m. Confirm any procedure details against the vehicle’s EPC or service information.
What system pressure and diagnostic trouble codes are listed for this high-pressure fuel pump?
The listed system pressure is 120 bar. The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. Use these as reference only; if a fact is not stated, confirm it against the vehicle’s EPC.
Does this pump require coding or adaptation, can I reuse the seals, and how do I verify the old part or service life?
Coding/adaptation, seal reuse, and expected service life are not stated in the provided facts; confirm them against the vehicle’s EPC or service information. To verify the old part, compare its part number with 06F127025K and the listed cross references 06F127025M, 06F127025J, 06F127025H, 06F127025F, and 06F127025B. If verification is not clear from the part number, confirm against the vehicle’s EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.