BOSCH 0445110343
for JAC Refine 4DA1 2.8L
1042200FA080, 0445110412F00VC01359DLLA150P18081600 bar peak rail pressureProduct Overview
The BOSCH 0445110343 (interchangeable with 0445110412) is a second-generation solenoid common rail fuel injector (CRI2.2 generation) engineered for the JAC HFC 4DA1-2B1 2.8L turbocharged diesel engine family. This powertrain, derived from the proven Isuzu 4JB1 architecture and modernized with Bosch high-pressure electronic fuel injection, powers the commercial JAC Refine MPV, Shuailing, and Junling light commercial vehicle platforms across global distribution markets. Operating at a peak system rail pressure of 1600 bar, the injector delivers multi-injection capability, dividing the combustion cycle into pilot injection (reducing mechanical noise and initial combustion shock), main injection (generating optimal brake mean effective pressure), and secondary post-injection for exhaust particulate control. The assembly relies on a calibrated balance between the upper control valve chamber pressure and the lower nozzle needle pressure pocket to govern needle lift dynamics.
Always verify the OE reference 1042200FA080 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 0445110343 needs its calibration code transferred after fitting; read the code from the new unit and program it with a compatible diagnostic tool.
Technical Specifications
| Specification | Value |
|---|---|
| INJECTOR TYPE | Common Rail Injector |
| SYSTEM PLATFORM | CRI |
| CONTROL VALVECore Spec | |
| NOZZLE CODECore Spec | |
| OPERATING PRESSURECore Spec |
Installation Tips
- Seat Cleanliness: Clean the cylinder head injector bore down to bare aluminum using a brass reaming brush and industrial vacuum. Any residual carbon under the copper washer will cause washer blowout.
- Washer Selection: Install a new, annealed 1.50mm copper seal. Never reuse a compressed copper washer.
- Anti-Seize Application: Apply a thin film of high-temperature ceramic mounting paste (such as Bosch ceramic grease) strictly to the injector body shaft. Keep paste completely off the nozzle tip and copper washer.
- Hold-Down Clamp Torque: Tighten the hold-down bracket bolt in a smooth, continuous motion to 30 N·m. Over-torquing deforms the internal needle sleeve and causes internal needle sticking.
- High-Pressure Pipe Torque: Align the high-pressure steel delivery pipe without mechanical tension; tighten the union nut to 25-30 N·m using a secondary counter-holding wrench on the injector inlet stud.
- Confirm the injector part number 0445110343 and its cross references against the vehicle's EPC before ordering.
- Tighten the injector hold-down to 30 N·m and the high-pressure line to 25-30 N·m with a calibrated torque wrench.
- Check for P0300, P0301, P0302, P0304, or P0087 and verify the listed Isuzu/JMC 4JB1 2.8L or JAC 2.8L fitment before replacement.
Frequently Asked Questions
Which vehicle applications and engine models use Bosch common rail injector 0445110343?
Bosch 0445110343 is factory equipment on the JAC HFC 4DA1-2B1 2.8-liter turbocharged common rail diesel engine (Euro 4 and Euro 5 emissions). This powertrain powers commercial light-duty vehicles including the JAC Refine 2.8 CRDi MPV, JAC Shuailing light commercial truck, and JAC Junling commercial delivery truck. It is fully interchangeable with Bosch part number 0445110412 and JAC original equipment (OE) number 1042200FA080.
What internal sub-components (nozzle and control valve) are required to overhaul 0445110343?
Rebuilding the 0445110343 injector requires genuine Bosch sub-components: nozzle assembly 0433172102 (stamped DLLA150P1808) with a 150-degree spray pattern, and control valve set F00VC01359. Maintaining calibrated spring preload and valve lift tolerances is critical for meeting ISO 4008 multi-injection delivery targets at 1600 bar.
What are the hold-down clamp torque and copper washer specifications for JAC 4DA1 2.8L injectors?
Tighten the injector hold-down clamp bolt to 30 N·m in a smooth, continuous sequence. Always fit a new, annealed 1.50 mm copper combustion seal washer (OD 15.0 mm, ID 7.1 mm) under the nozzle seat. Torque the high-pressure fuel rail delivery line union nut to 25-30 N·m while counter-holding the injector inlet stud with a secondary backing wrench to prevent internal body deformation.
What are the back-leak flow limits and does 0445110343 require IMA calibration coding?
Yes, the Bosch CRI2.2 injector features an alphanumeric IMA calibration code stamped on the plastic electrical connector that must be programmed into the engine ECU to equalize cylinder delivery. Back-leak return flow must not exceed 15 ml during a 10-second starter crank test, 10 to 25 ml/min at 350 bar idle rail pressure, and 45 ml/min under maximum load at 1600 bar. Return rates above these limits indicate control valve seat erosion triggering fault code P0087.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.