0445120357
Bosch Cummins ISDe 6.7L Injector 4988835 Data
4988835, 5263308, 4988834, 5263307, C4988835, C5263308F00RJ01692DLLA150P23861600 bar peak rail pressureProduct Overview
The Bosch 0445120357 (Dongfeng Cummins OE part numbers 4988835, 5263308, 4988834, and 5263307, with aftermarket remanufactured reference 0986435557) is an industrial-duty electro-hydraulic common rail diesel fuel injector belonging to the Bosch CRIN2-16 platform. Specifically calibrated for Dongfeng Cummins (DCEC) 4-cylinder ISDe 4.5L and 6-cylinder ISDe / ISB / QSB 6.7L electronic turbocharged diesel engines, it meets Euro 3, Euro 4, and EPA Tier 3 / EU Stage IIIA off-highway emission standards. Operating at high injection pressures up to 1600 bar, this injector provides precise pilot, main, and post-injection metering for heavy-duty commercial cargo vehicles (Dongfeng Tianlong Kinland, Tianjin Kingrun, Foton Auman), intercity transit passenger coaches (Yutong, King Long, Zhongtong), and heavy off-highway earthmoving machinery (XCMG, Liugong, SDLG). The hydraulic metering assembly utilizes an 8-hole micro-sac spray nozzle DLLA150P2386 (0433172386) matched with a high-speed precision balance valve assembly F00RJ01692. Accurate installation requires observing strict torque sequencing between the cylinder head clamp hold-down bolt and the side-feed high-pressure fuel connector quill tube to prevent pressurized diesel from leaking into the crankcase engine oil.
Always verify the OE reference 4988835, 5263308, 4988834, 5263307 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 0445120357 needs its calibration code transferred after fitting; read the code from the new unit and program it with a compatible diagnostic tool.
Vehicle & Engine Fitment
Technical Specifications
| Specification | Value |
|---|---|
| INJECTOR TYPE | Common Rail Injector |
| SYSTEM PLATFORM | CRI |
| CONTROL VALVECore Spec | |
| NOZZLE CODECore Spec | |
| OPERATING PRESSURECore Spec |
Installation Tips
- Inspection and Lubrication: Thoroughly clean the injector bore and the connector tube gallery with lint-free swabs. Inspect the sealing cone of the connector tube (4929864 / 4903290) for pitting or deformation; replace if indented. Lightly coat the O-ring seal on the connector tube with clean engine oil.
- Injector Preliminary Positioning: Install a fresh 1.5 mm copper crush washer onto the injector tip. Lower the injector into the cylinder head bore and press firmly by hand until seated. Install the hold-down clamp and finger-tighten the clamp bolt.
- Quill Tube Hand Alignment: Insert the side fuel connector tube through the cylinder head port into the injector side inlet. Thread the connector retaining nut by hand until the spherical tip contacts the injector seat. Do NOT tighten with a wrench yet.
- Injector Clamp Pre-Torquing: Torque the injector clamp hold-down bolt to an initial pre-torque of 15 N·m (prior to final 65 N·m) to draw the injector body into vertical alignment.
- Connector Retaining Nut Initial Torque: Torque the connector tube retaining nut to 20 N·m to seat the spherical tip into the injector port.
- Final Clamp Torquing: Tighten the injector clamp hold-down bolt to its final specification of 65 N·m (or 30 N·m + 90° angle rotation according to workshop manual DCEC SOP).
- Final Connector Tube Torquing: Finalize tightening the connector tube retaining nut to 50 N·m.
- High Pressure Pipe Torquing: Install the high-pressure fuel injection line from the common rail to the connector tube fitting and torque both flare nuts to 35 N·m.
- Verify part number 0445120357 before fitting the common-rail diesel injector.
- Tighten the injector mounting/hold-down to 65 N·m.
- Tighten the high-pressure line to 65 N·m.
Frequently Asked Questions
Which Cummins engines and commercial vehicles utilize Bosch injector 0445120357?
Bosch 0445120357 is calibrated for Dongfeng Cummins ISDe 4.5L and 6.7L (Euro 3 / Euro 4) and QSB 6.7L Tier 3 industrial engines. It fits Dongfeng Tianlong, Dongfeng Tianjin, Foton Auman cargo trucks, Yutong and King Long transit buses, and XCMG / Liugong / SDLG construction equipment from 2008 to 2021.
What are the genuine Cummins OE numbers for Bosch 0445120357?
Genuine Cummins OE part numbers include 4988835, 5263308, 4988834, and 5263307, with Bosch exchange reference 0986435557. It belongs to the heavy-duty Bosch CRIN2-16 platform.
What connector tube installation sequence is required for Cummins ISDe 6.7L?
Strictly observe the feed tube tightening sequence: install the injector and hand-tighten the clamp bolt; insert the high-pressure connector tube and torque its collar nut to 15 N·m to establish centering; then torque the injector hold-down bolt to its final specification of 65 N·m (or 30 N·m + 90°); and finally torque the connector tube collar nut to its full specification of 50 N·m.
Does Bosch 0445120357 require calibration coding after replacement?
Yes. The alphanumeric IMA code on the injector solenoid connector must be programmed into the Cummins CM2150 / CM850 ECM using Cummins INSITE or Bosch KTS diagnostic tools to balance fueling across all cylinders.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.