Catalog / CONTINENTAL / A2C59511605
CONTINENTAL

Continental VDO A2C59511605

View Specs
SolenoidContinental / VDO Common RailEuro 4

CR Pump High Pressure Fuel Pump

Reference data for CONTINENTAL A2C59511605 high-pressure fuel pump · OEM 8200430599, 8200663258, 8200821184 · Application 1.5 dCi, K9K
OE REFERENCE8200430599, 8200663258, 8200821184
CONTROL VALVE-
NOZZLE-
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / Pump Adaptation Required

This high-pressure fuel pump requires driver-demand adaptation or pump-learn programming (or at minimum a rail-pressure plausibility check) after fitting, using the vehicle manufacturer’s diagnostic tool, so the metering valve learns its new offset and the engine does not set a low-rail-pressure fault.

The Continental VDO (Siemens VDO) A2C59511605 is a CR-Pump (high-pressure fuel pump) for Renault Clio / Megane / Modus / Scenic and Nissan Qashqai / Tiida with the 1.5 dCi (K9K, 66/85 kW) engine. OE references: 8200430599, 8200663258, 8200821184 (VDO 5WS40153).

Before You Order

Confirm part A2C59511605 (Continental VDO), Renault 1.5 dCi (K9K) application, and 1600 bar system pressure before ordering; this high-pressure common-rail pump raises rail pressure and must be fitted with new seals.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Renault Clio III1.5 dCi (K9K)—
Renault Megane II1.5 dCi (K9K)—
Renault Scenic II1.5 dCi (K9K)—
Renault Modus1.5 dCi (K9K)—
Nissan Qashqai (J10)1.5 dCi (K9K)—
Nissan Tiida (C11)1.5 dCi (K9K)—
04

Technical Specifications

SpecificationValue
SKUA2C59511605
BrandCONTINENTAL
Fuel SystemContinental / VDO Common Rail
Operating PressureCore Spec
Hold Down Torque4 N·m + 65°
High-Pressure Line Torque25 N·m
Emission StandardEuro 4
System TypeHigh Pressure Fuel Pump
05

Installation Tips

  1. Depressurize the fuel system and isolate the ignition before opening any high-pressure connection.
  2. Clean the pump area and cap all fuel ports to prevent dirt ingress.
  3. Disconnect the fuel lines and electrical connector, then release the timing belt/chain or camshaft drive as applicable.
  4. Remove the old high-pressure pump and clean the mounting and sealing surfaces.
  5. Fit new seals and install the replacement high-pressure pump with the drive correctly aligned.
  6. Reconnect the fuel lines and electrical connector, ensuring all fittings are clean and seated.
  7. Prime the fuel circuit and check all high-pressure connections for leaks before start-up.
  8. Start the engine, verify rail pressure operation, and recheck for leaks.
Tips & Warnings:
  • Use new seals and keep high-pressure ports capped and clean;
  • confirm correct drive alignment by timing belt/chain or camshaft as applicable;
  • prime the fuel circuit and check for leaks before and after start-up;
  • do not reuse seals or allow dirt into the pump circuit.
06

Frequently Asked Questions

QWill this high-pressure common-rail fuel pump fit my Renault or Nissan 1.5 dCi K9K?

This high-pressure common-rail fuel pump is listed for Renault Clio III 1.5 dCi (K9K), Renault Megane II 1.5 dCi (K9K), Renault Scenic II 1.5 dCi (K9K), Renault Modus 1.5 dCi (K9K), and Nissan Qashqai (J10) 1.5 dCi (K9K). Confirm exact fitment against the vehicle EPC, since year/trim details are not stated.

QWhat diagnostic trouble codes or symptoms are associated with a failed unit?

The diagnostic trouble codes listed are P0300, P0087, P0201, P0204, and P0202. A symptom list is not stated, so confirm diagnosis and fault codes against the vehicle EPC or repair information instead of guessing.

QWhat are the mounting and high-pressure line torque specifications?

The mounting / hold-down torque is 4 N·m + 65°, and the high-pressure line torque is 25 N·m. The system pressure for this high-pressure common-rail fuel pump is 1600 bar.

QDoes this pump require coding/adaptation, can I reuse seals, and how do I verify the old part?

Coding/adaptation requirements and seal reuse guidance are not stated, so confirm them against the vehicle EPC or repair information. To verify the old unit, compare part number A2C59511605 and cross references 8200430599, 8200663258, 8200821184, and 5WS40153.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

P0300High

Random or Multiple Cylinder Misfire Detected

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol