Continental VDO A2C59513556
Piezo Common Rail Injector
9802448680, 1980S0, 1791017, AV6Q-9F593-AA, 31303994-M0012P1541600 bar peak rail pressureProduct Overview
The Continental Siemens VDO A2C59513556 is an authentic piezoelectric common rail diesel injector calibrated for Peugeot 308 I (4A_, 4C_) and 1.6 HDi engine platforms. Operating at an engineered rail pressure of 1600 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.
Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | A2C59513556 |
| Brand | CONTINENTAL |
| Fuel System | Continental / VDO Common Rail |
| Operating PressureCore Spec | |
| Hold Down Torque | 6 N·m + 180° |
| High-Pressure Line Torque | 25 N·m |
| Coding Required | VDO 6-Hex IIC |
| Emission Standard | Euro 5 |
| Injector Type | Piezoelectric |
Installation Tips
- Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
- Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
- Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
- Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
- Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
- Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 6 N·m, then rotate a further 180°, then reconnect the high-pressure line to the injector and tighten the line fitting to 25 N·m; keep the line aligned and free from side load.
- Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
- Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
- Before fitting, confirm the injector part number A2C59513556 against the vehicle's EPC or workshop manual.
- Keep the common-rail system clean and cap all openings until installation.
- After installation, follow the vehicle manufacturer's diagnostic and adaptation procedure if specified.
Frequently Asked Questions
Will this injector fit my vehicle?
It is listed for the Peugeot, Citroen, Ford and Volvo applications shown for part A2C59513556; confirm your engine code and vehicle details against the EPC or workshop data before ordering.
What symptoms suggest this common-rail diesel injector has failed?
The listing does not specify failure symptoms; for rough running, misfire, starting or smoke concerns, diagnose against the vehicle's workshop data before replacing part A2C59513556.
What should I check before ordering this injector?
Check the vehicle's engine code and application against the EPC or workshop manual, and confirm the existing injector part number matches A2C59513556 before ordering.
Does the replacement injector need coding or adaptation?
Coding or adaptation requirements are not stated for part A2C59513556; confirm the required procedure against the vehicle's EPC or workshop manual before fitting.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.