DELPHI EMBR00001D
Common Rail Injector for Peugeot 308 / 3008 DW10CTED4
9686191080, 1980S0, 1980.S0, 1681997, 9M5Q-9F593-BA28278897G3742000 bar peak rail pressureProduct Overview
The Delphi EMBR00001D is an authentic common rail diesel injector calibrated for Peugeot 308 / 3008 and DW10CTED4 engine applications. Operating at an engineered rail pressure of 2000 bar, this solenoid assembly features the precision 28278897 control valve and G374 nozzle. Mandatory ECU calibration requires programming the cylinder-specific C3i 20-digit code into the engine control unit to establish smooth delivery balance and Euro 5 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Peugeot 308 / 3008 | 2.0 HDi (DW10CTED4 163PS) | 2009-2015 |
| Peugeot 508 / 5008 | 2.0 HDi (DW10CTED4) | 2010-2015 |
| Citroen C4 / C5 (III) | 2.0 HDi (DW10CTED4) | 2009-2015 |
| Citroen DS4 / DS5 | 2.0 HDi (DW10CTED4) | 2011-2015 |
| Ford Mondeo (Mk4) | 2.0 TDCi (TXBA/UFBA) | 2010-2014 |
| Ford Kuga (Mk1) | 2.0 TDCi (TXDA) | 2010-2014 |
| Ford S-Max | 2.0 TDCi (TXWA/UFWA) | 2010-2014 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EMBR00001D |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 25 N·m |
| High-Pressure Line Torque | 28 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 5 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 25 N·m, then reconnect the high-pressure line and tighten it to 28 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Before installation, confirm EMBR00001D against the vehicle by VIN and EPC so the correct injector variant is fitted.
- Follow the vehicle workshop manual for any coding, adaptation, seal replacement, and torque requirements.
- Diagnose the original fault and keep the fuel system clean before fitting a common-rail injector.
Frequently Asked Questions
Will EMBR00001D fit my Peugeot or Citroen?
EMBR00001D is listed for the Peugeot and Citroen applications shown in the fitment data for the specified HDi engine family. Confirm by VIN or registration against the vehicle EPC before ordering.
What symptoms suggest the injector has failed?
Typical symptoms that warrant injector diagnosis include rough running, misfire, excessive smoke, poor starting, loss of power, and fuel smell. Confirm the fault with workshop diagnostics before replacing EMBR00001D.
What should I check before ordering EMBR00001D?
Check the vehicle's VIN or registration against the EPC, compare the original injector visually, and confirm the engine family and fitment listing for EMBR00001D. If coding or seal replacement is required, verify it in the workshop manual.
Must the old injector be matched or adapted?
Coding or adaptation requirements are not stated here for EMBR00001D. Before fitting, confirm whether the replacement needs matching to the vehicle and follow the vehicle EPC or workshop manual procedure.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.