Continental VDO A2C59514909
unit injector
03G130073D, 03G130073M, 03G130073T--1800 bar peak rail pressureProduct Overview
The Continental Siemens VDO A2C59514909 is an authentic piezoelectric Pumpe-Düse element (unit injector / pump-nozzle) calibrated for Volkswagen Passat B6 (3C2) and 2.0 TDI PPD, BMN, BMR, BRD engine platforms. As a camshaft-driven unit injector, it combines pump and nozzle in one assembly and features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.
Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Passat B6 (3C2) | 2.0 TDI 170PS (BMR) | 2006-2008 |
| Audi A4 B7 (8ED) | 2.0 TDI 170PS (BRD) | 2006-2008 |
| Seat Leon FR (1P1) | 2.0 TDI 170PS (BMN) | 2006-2010 |
| Skoda Octavia vRS (1Z3) | 2.0 TDI 170PS (BMN) | 2006-2008 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | A2C59514909 |
| Brand | CONTINENTAL |
| Fuel System | Continental / VDO Common Rail |
| Operating PressureCore Spec | |
| Hold Down Torque | 3 N·m + 90° + 180° |
| High-Pressure Line Torque | 25 N·m |
| Coding Required | VDO 6-Hex IIC |
| Emission Standard | Euro 4 |
| Injector Type | Piezoelectric |
Installation Tips
- Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
- Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
- Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
- Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
- Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
- Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 3 N·m, then rotate a further 90°, then a further 180°, then reconnect the high-pressure line to the injector and tighten the line fitting to 25 N·m; keep the line aligned and free from side load.
- Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
- Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
- Verify part number A2C59514909 and the listed cross references before fitting.
- Use the listed mounting/hold-down torque of 3 N·m + 90° + 180°.
- Tighten the high-pressure line to 25 N·m.
Frequently Asked Questions
Will part A2C59514909 fit my vehicle?
The listed fitment for part A2C59514909 is Volkswagen Passat B6 (3C2) 2.0 TDI 170PS (BMR) 2006-2008; Audi A4 B7 (8ED) 2.0 TDI 170PS (BRD) 2006-2008; Seat Leon FR (1P1) 2.0 TDI 170PS (BMN) 2006-2010; and Skoda Octavia vRS (1Z3) 2.0 TDI 170PS (BMN) 2006-2008. It is a common-rail diesel injector for the 2.0 TDI PPD, BMN, BMR, BRD engine family. Cross references listed are 5WS40073, 03G130073D, 03G130073M, and 03G130073T.
What fault codes might point to this injector?
The verified diagnostic trouble codes listed are P0300, P0087, P0201, P0204, and P0202. The facts provided do not list symptom descriptions beyond these codes.
What are the mounting and high-pressure line torque specs?
Mounting/hold-down torque is 3 N·m + 90° + 180°. High-pressure line torque is 25 N·m. The listed system pressure is 1800 bar.
Do I need coding or adaptation, and can I reuse the seals?
The verified facts do not state coding/adaptation requirements or seal-reuse guidance. Confirm both against the vehicle's EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when a Pumpe-Düse unit injector suffers camshaft-driven wear, solenoid or piezo faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.