Continental VDO 5WS40074
Piezo Common Rail Injector
03G130073T, 03G130073TX--1800 bar peak rail pressureProduct Overview
The Continental Siemens VDO 5WS40074 is an authentic piezoelectric common rail diesel injector calibrated for Volkswagen Passat Variant (3C5) and 2.0 TDI PPD engine platforms. Operating at an engineered rail pressure of 1800 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.
Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Passat Variant (3C5) | 2.0 TDI (BMR) | 2006-2008 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | 5WS40074 |
| Brand | CONTINENTAL |
| Fuel System | Continental / VDO Common Rail |
| Operating PressureCore Spec | |
| Hold Down Torque | 3 N·m + 90° + 180° |
| High-Pressure Line Torque | 25 N·m |
| Coding Required | VDO 6-Hex IIC |
| Emission Standard | Euro 4 |
| Injector Type | Piezoelectric |
Installation Tips
- Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
- Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
- Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
- Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
- Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
- Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 3 N·m, then rotate a further 90°, then a further 180°, then reconnect the high-pressure line to the injector and tighten the line fitting to 25 N·m; keep the line aligned and free from side load.
- Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
- Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
- Verify part number 5WS40074 and cross references A2C59514910, 03G130073T, and 03G130073TX before fitting.
- Tighten the high-pressure line to 25 N·m.
- Confirm coding/adaptation against the vehicle's EPC before installation.
Frequently Asked Questions
Will this common-rail diesel injector fit a 2006-2008 Volkswagen Passat Variant (3C5) 2.0 TDI BMR?
The listed fitment is Volkswagen Passat Variant (3C5) 2.0 TDI (BMR) (2006-2008), for the 2.0 TDI PPD, BMR engine family. The part number is 5WS40074, with cross references A2C59514910, 03G130073T, and 03G130073TX. Confirm fitment against the vehicle's EPC before ordering.
What are the mounting/hold-down torque and high-pressure line torque values?
The mounting/hold-down torque is 3 N·m + 90° + 180°. The high-pressure line torque is 25 N·m.
What diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0087, P0201, P0204, and P0202. Use these as reference codes only and confirm diagnosis against the vehicle's EPC.
Is coding or adaptation required for this injector, and what system pressure is listed?
Coding/adaptation requirements are not stated in the verified facts; confirm them against the vehicle's EPC instead of guessing. The listed system pressure is 1800 bar.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.