Catalog / CONTINENTAL / A2C59514910
CONTINENTAL

Continental VDO A2C59514910

View Specs
SolenoidContinental / VDO Pumpe-Düse (PD unit injector)Euro 4

Piezo Unit Injector (Pumpe Düse)

Reference data for CONTINENTAL A2C59514910 unit injector · OEM 03G130073S, 03G130073SX, 03G130073DX · Application 2.0 TDI PPD, BKP, BMA
OE REFERENCE03G130073S, 03G130073SX, 03G130073DX
CONTROL VALVE-
NOZZLEM0005P153
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Continental Siemens VDO A2C59514910 is an authentic piezoelectric Pumpe-Düse-Element (unit injector / pump-nozzle) calibrated for Volkswagen Passat B6 (3C2) and 2.0 TDI PPD, BKP, BMA engine platforms. This camshaft-driven unit combines pump and nozzle in one assembly, with ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.

Before You Order

Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Volkswagen Passat B6 (3C2)2.0 TDI 140PS (BKP)2005-2008
Volkswagen Touran (1T1)2.0 TDI 140PS (BKP)2005-2010
04

Technical Specifications

SpecificationValue
SKUA2C59514910
BrandCONTINENTAL
Fuel SystemContinental / VDO Common Rail
Operating PressureCore Spec
Hold Down Torque3 N·m + 90° + 180°
High-Pressure Line Torque25 N·m
Coding RequiredVDO 6-Hex IIC
Emission StandardEuro 4
Injector TypePiezoelectric
05

Installation Tips

  1. Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
  2. Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
  3. Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
  4. Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
  5. Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
  6. Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 3 N·m, then rotate a further 90°, then a further 180°, then reconnect the high-pressure line to the injector and tighten the line fitting to 25 N·m; keep the line aligned and free from side load.
  7. Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
  8. Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
Tips & Warnings:
  • Verify the part number A2C59514910 and cross references 5WS40074, 03G130073S, 03G130073SX, and 03G130073DX before fitting.
  • Apply the listed hold-down torque of 3 N·m + 90° + 180° and high-pressure line torque of 25 N·m.
  • Confirm seal replacement and exact application against the vehicle's EPC before installation.
06

Frequently Asked Questions

QWill this common-rail diesel injector fit my vehicle?

It is listed for Volkswagen Passat B6 (3C2) 2.0 TDI 140PS (BKP) (2005-2008) and Volkswagen Touran (1T1) 2.0 TDI 140PS (BKP) (2005-2010). It is for the 2.0 TDI PPD, BKP, BMA engine family. If your vehicle is not exactly one of these applications, confirm fitment against the vehicle's EPC before ordering.

QWhat diagnostic trouble codes are associated with this injector?

The listed diagnostic trouble codes are P0300, P0087, P0201, P0202, and P0204. Any further code interpretation or fault diagnosis is not stated in the supplied facts and must be confirmed against the vehicle's EPC.

QWhat are the mounting and high-pressure line torques for this injector?

The mounting/hold-down torque is 3 N·m + 90° + 180°. The high-pressure line torque is 25 N·m. The system pressure listed for this common-rail diesel injector is 1800 bar.

QDoes this injector require coding or adaptation after installation?

Coding or adaptation requirements for this common-rail diesel injector are not stated in the supplied facts. That information must be confirmed against the vehicle's EPC instead of guessing.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when a Pumpe-Düse unit injector suffers camshaft-driven wear, solenoid or piezo faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

P0300High

Random or Multiple Cylinder Misfire Detected

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

CRDI WORKSHOP ENGINEERING & DIAGNOSTICS

Piezo Injector 10 Bar Backleak & Stalling Guide

Bosch CRI3 piezo injector 10 bar backleak pressure guide. Diagnose hydraulic coupler cavitation, overflow valve failure, return line stalling & P0087.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol