Catalog / CONTINENTAL / A2C59514914
CONTINENTAL

Continental VDO A2C59514914

View Specs
SolenoidContinental / VDO Pumpe-Düse (PD unit injector)Euro 4

unit injector

Reference data for CONTINENTAL A2C59514914 unit injector · OEM 03G130073DX · Application 2.0 TDI PPD, BMN
OE REFERENCE03G130073DX
CONTROL VALVE-
NOZZLE-
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Continental Siemens VDO A2C59514914 is an authentic piezoelectric Pumpe-Düse (unit injector / pump-nozzle) element calibrated for Seat Altea (5P1) and 2.0 TDI PPD BMN engine platforms. As a camshaft-driven assembly, the pump and nozzle form one unit, with piezo actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.

Before You Order

Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Seat Altea (5P1)2.0 TDI (BMN)2006-2010
Skoda Octavia II RS2.0 TDI (BMN)2006-2008
04

Technical Specifications

SpecificationValue
SKUA2C59514914
BrandCONTINENTAL
Fuel SystemContinental / VDO Common Rail
Operating PressureCore Spec
Hold Down Torque3 N·m + 90° + 180°
High-Pressure Line Torque25 N·m
Coding RequiredVDO 6-Hex IIC
Emission StandardEuro 4
Injector TypePiezoelectric
05

Installation Tips

  1. Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
  2. Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
  3. Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
  4. Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
  5. Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
  6. Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 3 N·m, then rotate a further 90°, then a further 180°, then reconnect the high-pressure line to the injector and tighten the line fitting to 25 N·m; keep the line aligned and free from side load.
  7. Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
  8. Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
Tips & Warnings:
  • Verify part number A2C59514914 and cross references 5WS40073 and 03G130073DX before fitting.
  • Tighten the high-pressure line to 25 N·m.
  • Tighten the mounting/hold-down to 3 N·m + 90° + 180°.
06

Frequently Asked Questions

QWhich vehicles does this common-rail diesel injector fit?

It fits Seat Altea (5P1) 2.0 TDI (BMN) 2006–2010 and Skoda Octavia II RS 2.0 TDI (BMN) 2006–2008. The engine family is 2.0 TDI PPD, BMN. Confirm final fitment against the vehicle's EPC.

QWhat diagnostic trouble codes can indicate an issue with this injector?

The verified diagnostic trouble codes are P0300, P0087, P0201, P0204, and P0202. Use these as diagnostic references and confirm the actual fault on the vehicle. The facts do not state other symptoms.

QDo I need to code this injector or can I reuse the seals?

The verified facts do not state coding/adaptation requirements or whether seals can be reused. Confirm both against the vehicle's EPC instead of guessing.

QHow do I verify the old part and what are the mounting and high-pressure line torques?

Check part number A2C59514914 and cross references 5WS40073 and 03G130073DX. Mounting/hold-down torque is 3 N·m + 90° + 180°, and high-pressure line torque is 25 N·m. This common-rail diesel injector is listed with 1800 bar system pressure. Confirm any unstated installation details against the vehicle's EPC.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when a Pumpe-Düse unit injector suffers camshaft-driven wear, solenoid or piezo faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

P0300High

Random or Multiple Cylinder Misfire Detected

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

CRDI WORKSHOP ENGINEERING & DIAGNOSTICS

Piezo Injector 10 Bar Backleak & Stalling Guide

Bosch CRI3 piezo injector 10 bar backleak pressure guide. Diagnose hydraulic coupler cavitation, overflow valve failure, return line stalling & P0087.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol