Delphi EJBR03601D
common rail injector
33800-4X900, 33801-4X90028239294L175PRD1600 bar peak rail pressureProduct Overview
The Delphi EJBR03601D is an authentic common rail diesel injector calibrated for Kia Bongo III and J3 CRDi engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and L175PRD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 4 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR03601D |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 38 N·m |
| High-Pressure Line Torque | 35 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 4 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 38 N·m, then reconnect the high-pressure line and tighten it to 35 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Tighten the injector mounting / hold-down to 38 N·m.
- Tighten the high-pressure line to 35 N·m.
- Confirm EJBR03601D or a listed cross reference against the vehicle's EPC before fitting.
Frequently Asked Questions
How can I confirm EJBR03601D fits my Kia and verify the old injector?
EJBR03601D is a common-rail diesel injector for the J3 CRDi / Bongo J3 engine family, listed for Kia Bongo III 2.9 CRDi (J3) 2006-2012 and Kia K2900 2.9 CRDi (J3) 2007-2012. Compare the old unit against EJBR03601D or the listed cross references EJBR02901D, 33800-4X900, and 33801-4X900. Confirm the final fitment against the vehicle's EPC before ordering.
Which diagnostic trouble codes are listed for this injector?
The verified diagnostic trouble codes listed are P0300, P0087, P0201, P0204, and P0202. Use the old part number and vehicle EPC to confirm the correct replacement before fitting.
What are the mounting / hold-down and high-pressure line torque values?
The mounting / hold-down torque is 38 N·m, and the high-pressure line torque is 35 N·m. The system pressure for this common-rail diesel injector is 1600 bar.
Does EJBR03601D require coding or adaptation after installation?
The verified facts do not state a coding or adaptation requirement for EJBR03601D. Any coding or adaptation requirement must be confirmed against the vehicle's EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.