095000-5450
Denso Komatsu PC400 8 Injector 6271 11 3100 Specs
6271-11-3100, 6271-11-3101, 6271-11-3102, 095000-5451, 095000-5452, 095000-5453, 095000-5454, 095000-5459PLATE 10# / DENSO G2 VALVE PLATEDLLA145P8751800 bar peak rail pressureProduct Overview
The DENSO 095000-5450 is an authentic original-equipment G2 common rail diesel fuel injector engineered specifically for Komatsu SAA6D125E-5 (6-cylinder, 11.04-liter, 257 kW / 345 hp) turbocharged electronically controlled diesel engines. Meeting EPA Tier 3 and EU Stage IIIA non-road industrial emissions standards, this injector is the primary combustion component deployed across Komatsu PC400-8, PC400LC-8, PC450-8, PC450LC-8, and PC500LC-8 heavy mining crawler excavators, WA470-6 and WA480-6 heavy wheel loaders, and D65EX-16 crawler dozers. Operating at rail pressures up to 1800 bar (26,100 psi) supplied by Denso HP3/HP4 high-pressure fuel supply pumps, this injector incorporates a calibrated DLLA145P875 multi-hole nozzle (Denso part number 093400-8750) and a hardened Plate 10# electro-hydraulic spool control valve to achieve precise micro-pilot, main, and split post-injection cycles. Denso part number 095000-5450 supersedes and interchanges directly with revisions 095000-5451, 095000-5452, 095000-5453, and 095000-5459, and corresponds directly to Komatsu OEM references 6271-11-3100, 6271-11-3101, and 6271-11-3102.
CRITICAL WORKSHOP NOTICE: Always photograph or manually record the 30-digit Denso QR Compensation Code laser-etched onto the injector solenoid cap BEFORE installation. Once the injector is seated in the cylinder head, this calibration code cannot be read. Denso 095000-5450 (Komatsu OEM 6271-11-3100 / 6271-11-3101 / 6271-11-3102) is the flagship electro-hydraulic G2 common rail injector powering Komatsu SAA6D125E-5 (11.0L 6-cylinder, 257 kW / 345 hp) Tier 3 / Stage IIIA diesel engines in Komatsu PC400-8, PC450-8, and PC500LC-8 heavy mining excavators and WA470-6 / WA480-6 wheel loaders. Tighten the injector hold-down clamp bolt to 30 N·m (22 lb·ft) and the high-pressure fuel feed line nut to 30 N·m (22 lb·ft). Writing the 30-digit QR code into the engine ECM via Komatsu Service Tool / INSITE is mandatory to avoid severe idle vibration, cylinder contribution imbalances, and black smoke under heavy hydraulic breakout load.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | 095000-5450 |
| Brand | DENSO |
| Type | G2 Common Rail Fuel Injector |
| OE Number | 6271-11-3100, 6271-11-3101, 6271-11-3102, 095000-5451 |
| Injection System | Denso Common Rail System (CRS ECD-U2 / G2) |
| Operating PressureCore Spec | |
| Torque Spec | 30 N·m |
| Hold Down Torque | 30 N·m |
| Warranty | 12 Months |
| Emission Standard | EPA Tier 3 / EU Stage IIIA |
| Engine Family | Komatsu SAA6D125E-5 (11.0L 6-Cylinder) |
| Coding Required | Yes (Denso 30-Digit QR Compensation Code / Komatsu Service Tool) |
Installation Tips
Tools needed: Calibrated torque wrench (10-60 N·m range), Komatsu Service Tool (PC-Service Tool) or INSITE diagnostic interface, Denso QR code reader or high-resolution smartphone camera, Injector bore reamer and copper seat cleaning brush kit, Lint-free industrial cleaning swabs, Clean engine oil or assembly lubricant for O-rings, High-pressure fuel injection pipe socket (17 mm flare nut wrench), Compressed air line with rubber nozzle
- Clean Cylinder Head Bore and Ream Seat: Thoroughly clean the injector bore down to the bottom copper washer landing. Use an injector seat reamer to remove carbon glaze, varnish, and old washer debris. Blow out debris with dry compressed air while plugging the nozzle tip passage. Ensure the seating surface is 100% flat, clean, and dry.
- Install New Copper Sealing Washer and O-Rings: Fit a new genuine OEM copper washer (thickness ~1.5 mm) onto the injector nozzle body. Never reuse an old compressed washer. Lightly lubricate the upper body rubber O-ring with clean engine oil to prevent shearing or binding upon insertion into the rocker housing.
- Seat Injector and Tighten Clamp Bolt: Carefully lower the injector vertically into the cylinder head bore until the copper washer firmly contacts the cylinder head seat. Position the hold-down clamp fork centrally over the injector shoulder. Torque the clamp retaining bolt evenly to 30 N·m (22 lb·ft).
- Connect High-Pressure Rail Line and Solenoid Harness: Hand-thread the high-pressure fuel pipe union nuts onto the fuel rail and injector inlet fittings to guarantee cross-thread prevention. Final torque both line nuts to 30 N·m (22 lb·ft). Connect the two electrical solenoid terminals and torque retaining nuts gently to 2.5 N·m (22 lb·in).
- Bleed Fuel System and Program Denso 30-Digit QR Code: Connect the Komatsu Service Tool. Select Injector Calibration / Compensation Code Registration and input the 30-digit alphanumeric QR code recorded before installation for the specific cylinder. Prime the fuel system using the manual hand pump, start the engine, and perform an automated high-pressure rail leak test and cylinder cut-out test.
- Verify the machine model, engine family SAA6D125E-5, and model year against the vehicle’s EPC before ordering.
- Tighten the mounting/hold-down and high-pressure line to the listed 30 N·m values.
- Compare the old injector markings with 095000-5450 and the listed cross references before installation.
Frequently Asked Questions
Will part 095000-5450 fit my Komatsu PC450-8?
Part 095000-5450 is listed as a common-rail diesel injector for the Komatsu SAA6D125E-5 engine family. Fitment includes Komatsu PC450-8 / PC450LC-8 with SAA6D125E-5 for 2006-2016. Confirm the exact machine application against the vehicle’s EPC before ordering.
What pressure and torque values apply to this injector?
The listed system pressure is 1800 bar. The mounting/hold-down torque is 30 N·m, and the high-pressure line torque is 30 N·m.
What diagnostic trouble codes are listed for this injector?
The diagnostic trouble codes listed for this injector are P0300, P0301, P0087, P0302, and P0304. Any diagnostic interpretation or code-setting procedure beyond that list must be confirmed against the vehicle’s EPC instead of guessing.
How can I verify the old injector before ordering?
Check the old injector marking against part number 095000-5450 and the listed cross references: 0950005450, 6271113100, 6271113101, 6271113102, 0950005451, and 0950005452. Also confirm the machine model, engine family SAA6D125E-5, and model year against the vehicle’s EPC. If a marking is not listed, confirm it against the EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.