Catalog / DENSO / 095000-9770
DENSO

095000-9770

View Specs
SolenoidDenso Common Rail System (CRS)Euro 6

Denso Kubota V3307 Injector 1J770 53051 Specs

Reference data for DENSO 095000-9770 common rail injector · OEM 1J770-53050, 1J770-53051, 1J770-53070, 1J770-53071, 1J770-53072, 1J770-53074, 7000767, 7256789 · Application Kubota V3307 / V3800 (3.3L & 3.8L CR-TE4)
OE REFERENCE1J770-53050, 1J770-53051, 1J770-53070, 1J770-53071, 1J770-53072, 1J770-53074, 7000767, 7256789
CONTROL VALVEPLATE
NOZZLEDLLA148P985
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Denso 095000-9770 common rail diesel injector is an OEM high-pressure unit manufactured for Kubota V3307-CR-TE4 and V3307-CR-TIE4 3.3-liter turbocharged industrial engines. Widely equipped on Kubota M-Series utility tractors (M6040, M7040, M8540, M9540, M7060), Kubota SVL75 track loaders, and Bobcat commercial machinery (S750, S770, T750, T770, E85), this G3 solenoid injector operates at operating pressures up to 1800 bar (26,100 psi). The internal hydraulic system integrates a precision-matched DLLA148P985 multi-hole nozzle and a hardened #10/#29 orifice valve plate assembly, delivering multi-pilot, main, and post-injection events for optimized combustion efficiency and stringent particulate matter compliance.

Before You Order

Crucial Workshop Notice: Denso 095000-9770 (Kubota 1J770-53051 / 1J770-53070) operates under Tier 4 Final / Stage IV high-precision injection timing. Always inspect high-pressure rail pipe seating and replace cylinder copper washer (1J770-53620, 1.5 mm). ECU recalibration with the 30-digit Denso QR code is mandatory via Kubota Diagmaster or Bobcat Service Analyzer to prevent DPF premature clogging and cylinder knocking.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
Aftermarket
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Kubota M-SeriesV3307 / V38002012-2022
Kubota Compact Track Loaders (SVL75 / SVL75-2)V3307 / V38002012-2022
Bobcat Skid-Steer Loaders (S750 / S770 / S850)V3307 / V38002013-2020
Bobcat Compact Track Loaders (T750 / T770 / T870)V3307 / V38002013-2020
04

Technical Specifications

SpecificationValue
INJECTOR TYPECommon Rail Injector
SYSTEM PLATFORMCRI
CONTROL VALVECore Spec
NOZZLE CODECore Spec
OPERATING PRESSURECore Spec
05

Installation Tips

  1. Depressurize And Isolate: Shut down the engine, allow it to cool, relieve fuel pressure at the service point, isolate the fuel supply, lock out the source, and confirm no residual pressure remains before opening any high-pressure connection.
  2. Clean Surrounding Area: Clean the cylinder head around the injector bore and high-pressure connection, remove loose debris with a lint-free method, and plug or cap openings to keep contaminants out of the injector bore and high-pressure line.
  3. Disconnect And Remove Line: Disconnect the injector electrical connector and the spill/return connection, cap all exposed ports, then slowly loosen and remove the high-pressure line from the injector and high-pressure connection; cap both ends and discard the line if damaged.
  4. Extract And Clean Bore: Extract the old injector from the injector bore, then clean the bore and seat without scoring; install new seals including a new copper combustion washer and seat the injector squarely in the bore.
  5. Tighten Hold-Down: Install the hold-down fastener and tighten the hold-down to 30 N·m; confirm the injector stays aligned and the new copper combustion washer remains correctly seated.
  6. Reconnect High-Pressure Line: Fit the high-pressure line to the injector and high-pressure connection, align the fittings without side load, and tighten the line to 32 N·m; replace the line if the service procedure requires it.
  7. Calibration Coding: Record the 30-digit Denso QR code and program it with a compatible diagnostic tool.
  8. Leak-Check And Start-Up: After coding, perform a leak check of the high-pressure line and injector connections, start the engine, allow it to idle, inspect for leaks, and shut down immediately if any leak or abnormal noise appears.
Tips & Warnings:
  • Torque the injector hold-down to 30 N·m.
  • Tighten the high-pressure line to 32 N·m.
  • Verify the old injector part number against 095000-9770 or the listed cross references before ordering.
06

Frequently Asked Questions

QWhich Kubota tractors and Bobcat skid steers use Denso injector 095000-9770?

Denso 095000-9770 is designed for Kubota V3307-CR-TE4 and V3307-CR-TIE4 (3.3L, Tier 4 Final / Stage IV) common rail diesel engines. It powers Kubota M6040, M7040, M8540, M9540, M6060, M7060 tractors, Kubota SVL75-2 and SSV75 loaders, and Bobcat S750, S770, S850, T750, T770, T870 loaders and E85 excavators from 2012 to 2022.

QWhat are the genuine Kubota OE part numbers for Denso 095000-9770?

Official Kubota part numbers include 1J770-53051, 1J770-53070, 1J770-53050, and 1J770-53052. The injector assembly features the Denso DLLA148P985 nozzle and operates at 1,800 bar rail pressure.

QIs QR compensation coding required when installing 095000-9770 on Tier 4 Kubota engines?

Yes. The 30-digit alpha-numeric QR code on the electrical connector must be written to the engine ECU using Kubota Diagmaster or Bobcat Service Software. Precise QR calibration is mandatory on Tier 4 Final engines to maintain tight DPF and DOC soot balance.

QWhat is the hold-down clamp torque specification for Denso 095000-9770?

Torque the hold-down clamp bolt to 30 N·m. Always install a new genuine Kubota 1.5 mm copper washer (part number 1J770-53620) and verify that the injector nozzle seat is completely free of carbon build-up.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol