BOSCH FT4Z-9F593-A
Direct Fuel Injector Ford F 150 Edge ST Fusion Lincoln MKX 2.7L EcoBoost V6 0261500298
0261500298, CM5248, FJ1234--150 bar peak rail pressureProduct Overview
The FT4Z-9F593-A is an original equipment (BOSCH) precision component engineered specifically for the Ford 2.7L EcoBoost Twin-Turbo DOHC 24V V6 Nano. Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0302, P0172.
Always verify the OE reference CM5248, FJ1234 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. FT4Z-9F593-A needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | FT4Z-9F593-A |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | Ford 2.7L EcoBoost Twin-Turbo DOHC 24V V6 Nano |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 20 N-m (15 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0302, P0172 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 20 N-m (15 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Use the VIN and EPC to confirm the exact application before ordering.
- Inspect the connector and sealing surfaces, then confirm seal reuse and torque against the workshop manual.
- Diagnose misfire or fuel-trim faults with workshop data before condemning the injector.
Frequently Asked Questions
Will FT4Z-9F593-A fit my Ford or Lincoln?
It is listed for the Ford and Lincoln EcoBoost Nano Twin-Turbo applications shown in the fitment above. Confirm by VIN and the vehicle’s EPC before ordering, as trims and production changes can affect compatibility.
What symptoms suggest a failed injector?
Look for rough idle, misfire, hesitation, poor cold-start behaviour, a fuel smell, or an illuminated check-engine light. Confirm diagnosis with the vehicle’s workshop data before replacing the injector.
What should I check before ordering a replacement?
Verify the VIN, engine variant, connector type, and the original injector part number against the EPC. Also confirm any coding, seal-reuse, and tightening requirements in the workshop manual before fitting.
Must the new injector be matched or adapted?
Matching or adaptation requirements are not stated here. Check the vehicle’s EPC and workshop manual for coding or relearn instructions, and follow the manufacturer’s procedure before starting the engine.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.