Catalog / BOSCH / JL3Z-9F593-A
BOSCH

BOSCH JL3Z-9F593-A

View Specs
SolenoidGasoline Direct Injection (GDI / HDEV)Euro 6

Direct Fuel Injector Ford F 150 Mustang 5.0L Coyote V8 Gen 3 PFDI 0261500360

Reference data for BOSCH JL3Z-9F593-A common rail injector · OEM 0261500360, 0261500361, FJ1431, JL3E-9F593-AB · Application Ford 5.0L Coyote V8 (Gen 3 PFDI Dual-Fuel Ti-VCT)
OE REFERENCE0261500360, 0261500361, FJ1431, JL3E-9F593-AB
CONTROL VALVEHIGH-RESPONSE MULTI-HOLE ELECTROMAGNETIC NOZZLE
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The BOSCH JL3Z-9F593-A is an OEM Tier-1 precision-engineered fuel system component built to strict factory tolerances. Engineered for modern high-performance gasoline engines, this component delivers precise fuel metering, maintains stable fuel rail pressure, and mitigates cold-start misfire, engine oil dilution, and acceleration hesitation under demanding driving conditions.

Before You Order

Always verify the OE reference FJ1431, JL3E9F593AB stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. JL3Z-9F593-A needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Ford F-1505.0L V8 Coyote Gen 3 PFDI2018-2023
Ford Mustang GT5.0L V8 Coyote Gen 3 PFDI2018-2023
Ford Mustang Mach 15.0L V8 Coyote Gen 3 PFDI2021-2023
04

Technical Specifications

SpecificationValue
System TypeFord Port Fuel & Direct Injection (PFDI) 250-bar System
Operating PressureCore Spec
Spray PatternLaser-Drilled Multi-Hole Symmetrical Spray Cone
Injector Hold-Down Bolt Torque10 N·m (89 in-lb) direct fuel rail securing bolts📐 Torque & Angle Wizard →
Fuel Line Nut Torque28 N·m (21 lb-ft) high-pressure crossover tube union nut
Combustion SealVirgin PTFE Teflon Sealing Ring (Pre-compressed)
Upper Rail O-RingFluorocarbon (FKM) High-Temp Bio-Ethanol Resistant
ManufacturerBosch (OEM for Ford Motor Company)
Bosch Production Number0261500360 / 0261500361
05

Installation Tips

  1. Dual-Fuel System Depressurization & Preparation: Depressurize both port fuel and direct injection systems by disabling the low-pressure fuel pump fuse and running engine until stall. Disconnect battery negative terminal.
  2. Intake Manifold & Upper Port Injection Rail Removal: Remove intake air ducting and throttle body connections. Disconnect low-pressure port injector wiring harness and unbolt upper intake manifold assembly to access the direct injection rail beneath.
  3. Direct Injection Rail & Steel Fuel Line Removal: Disconnect high-pressure direct fuel injector electrical plugs. Using a flare wrench, loosen the high-pressure crossover tube fittings. Remove fuel rail hold-down bolts (10 N·m) and withdraw rail with injectors.
  4. Cylinder Head Bore Cleaning & PTFE Seal Pre-Fitting: Clean injector combustion bores in the cylinder head using brass soft brushes and lint-free swabs. Ensure the pre-installed Teflon seal ring on the new Bosch injector is undamaged and free of engine oil/grease.
  5. Rail Alignment & Torque Specification Adherence: Lightly lubricate upper FKM O-rings with clean engine oil (keep lower Teflon dry). Press injectors into cylinder head bores, position direct fuel rail, and torque mounting bolts in two passes up to 10 N·m.
  6. High-Pressure Line Torquing & Engine Leak Inspection: Reinstall high-pressure fuel lines and torque flare nuts to 28 N·m. Reinstall intake manifold and port injection components. Cycle ignition 3 times to prime system and perform high-pressure fuel leak diagnostic check.
Tips & Warnings:
  • Before fitting JL3Z-9F593-A, confirm the exact application and any coding or adaptation procedure in the vehicle's EPC or workshop manual.
  • Use vehicle-specific diagnostics and workshop data to confirm an injector fault rather than relying on symptoms alone before replacing JL3Z-9F593-A.
  • Confirm the vehicle's exact application in the EPC before ordering or installing JL3Z-9F593-A.
06

Frequently Asked Questions

QDoes JL3Z-9F593-A fit my Ford?

JL3Z-9F593-A is listed for the Ford Coyote PFDI truck and Mustang applications in the fitment data; confirm exact model, engine, and VIN coverage against the vehicle's EPC or workshop manual before ordering.

QWhat symptoms point to a failed injector?

The listing does not specify failure symptoms; use the vehicle's workshop manual and diagnostic data to confirm whether JL3Z-9F593-A is the cause before replacement.

QWhat should I check before ordering?

Confirm fitment against the vehicle's EPC or workshop manual, verify the listed Ford Coyote PFDI application, and check that the existing injector fault is diagnosed before ordering JL3Z-9F593-A.

QDoes the replacement injector need coding or matching?

Coding or matching requirements are not stated for JL3Z-9F593-A; confirm the required procedure against the vehicle's EPC or workshop manual before installation.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
DIESEL WORKSHOP DIAGNOSTIC SOP

Cylinder Balance & Injector Deviation Guide

Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol