BOSCH JR3Z-9F593-A
GDI Fuel Injector Ford Mustang GT Bullitt F 150 5.0L Coyote V8 0261500412
JR3Z-9F593-B, 0261500413, CM5278, 0261500412--200 bar peak rail pressureProduct Overview
The JR3Z-9F593-A is an original equipment (BOSCH) precision component engineered specifically for the Ford 5.0L Coyote Ti-VCT Dual-Fuel DOHC 32V V8 (Gen 3 Coyote). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0172.
Always verify the OE reference JR3Z9F593B, CM5278 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. JR3Z-9F593-A needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | JR3Z-9F593-A |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | Ford 5.0L Coyote Ti-VCT Dual-Fuel DOHC 32V V8 (Gen 3 Coyote) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 22 N-m (16 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0172 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 22 N-m (16 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Before removing the old injector, confirm JR3Z-9F593-A against the EPC using the vehicle identifier.
- Keep the work area clean and follow the workshop manual for injector removal and installation; confirm any torque value against the vehicle data.
- Do not assume coding or seal reuse; check the workshop manual for matching and sealing requirements before fitting JR3Z-9F593-A.
Frequently Asked Questions
Does JR3Z-9F593-A fit my Ford pickup or Mustang?
It is listed for the Ford pickup application and Mustang GT and other listed Mustang applications with the Coyote PFDI engine; confirm your exact vehicle and part number against the EPC before ordering.
What symptoms indicate a failed JR3Z-9F593-A?
Symptoms are not specified for this injector; use the vehicle's workshop manual diagnostic flow to confirm a failed unit before replacing JR3Z-9F593-A.
What should I check before ordering JR3Z-9F593-A?
Confirm your vehicle is the listed Ford pickup or Mustang application with the Coyote PFDI engine, and verify JR3Z-9F593-A against the EPC using the vehicle identifier.
Must the old injector be matched or adapted to JR3Z-9F593-A?
Coding or adaptation requirements are not stated here; confirm whether the replacement JR3Z-9F593-A needs matching against the vehicle's EPC or workshop manual before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.