BOSCH JX6G-9F593-AA
High Pressure Fuel Injector Ford Focus Mk4 Fiesta ST Kuga 1.5T Dragon EcoBoost 0261500824
JX6Z-9F593-A, 0261500824, 0261500595HIGH-PRESSURE MULTI-HOLE DIRECT SOLENOID VALVE-250 bar peak rail pressureProduct Overview
The Bosch JX6G-9F593-AA (Bosch 0261500824) is a Bosch HDEV5 250-bar high-pressure gasoline direct injector for Ford 1.5L EcoBoost Dragon three-cylinder Ti-VCT turbo engines. It is listed for the Ford Focus Mk4 (2018-2023), Fiesta ST Mk8 (2018-2023) and Kuga Mk3 (2019-2024). Rail pressure reaches 250 bar (25 MPa / 3625 psi), and the injector is matched to the three-cylinder asymmetric firing order with selective cylinder deactivation; solenoid resistance is 1.6-2.0 Ω at 20°C. Retaining clamp screws take 11 N·m and the fuel delivery pipe flare connection 26 N·m. Common codes are P0300, P0301-P0303 and P0171. Teflon tip seals must not be reused, and the cylinder deactivation solenoid connectors should be secured during harness routing.
Always verify the OE reference JX6Z9F593A stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. JX6G-9F593-AA needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDEV5 250-bar High-Pressure Gasoline Direct Injector |
| Operating PressureCore Spec | |
| Combustion Architecture | Optimized for 3-cylinder asymmetric firing order with selective cylinder deactivation |
| Fuel Rail Bolt Torque | 11 N·m (retaining clamp screws) |
| High Pressure Line Torque | 26 N·m (fuel delivery pipe flare connection) |
| Solenoid Coil Resistance | 1.6 - 2.0 Ω at 20°C (rapid pulse inductive circuit) |
| Common Fault Codes | P0300 (Random Misfire), P0301-P0303 (Cylinder Misfire), P0171 (Fuel Trim System Lean) |
| Workshop Precaution | Do not reuse Teflon tip seals; ensure cylinder deactivation solenoid connectors are secured during harness routing |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Relieve Fuel Pressure & Disconnect 12V Battery Ground: Depressurize fuel rail via scan tool command or fuel pump inertia switch cutout. Disconnect battery negative ground post before servicing.
- Remove Air Ducting, Harness Plugs & Fuel Rail Fasteners: Disconnect charge air hoses over cylinder head. Unclip electrical harness connections from direct injectors. Loosen fuel rail retaining fasteners (11 N·m).
- Withdraw Direct Injectors & Fit Fresh Teflon Tip Seals: Extract direct injectors using slide puller adapter. Inspect nozzle tip micro-orifices. Install fresh Teflon combustion seal ring and reshape using resizing tool.
- Torque Fuel Rail Bolts & High Pressure Fuel Unions: Position injectors into cylinder head ports. Tighten rail hold-down bolts to 11 N·m. Torque high pressure fuel pipe nut to 26 N·m. Start engine and verify zero leakage.
- Tighten the injector mounting/hold-down to 11 N·m.
- Tighten the high-pressure line to 26 N·m.
- Confirm the part number JX6G-9F593-AA and cross references before installation.
Frequently Asked Questions
What vehicles does part number JX6G-9F593-AA fit?
This gasoline direct-injection injector, part number JX6G-9F593-AA, is listed for the Ford 1.5L EcoBoost Dragon (3-Cylinder Ti-VCT Turbo) in Ford Focus Mk4 2018-2023, Ford Fiesta ST Mk8 2018-2023, and Ford Kuga Mk3 2019-2024. For any vehicle not covered by that list, confirm fitment against the vehicle's EPC.
What diagnostic trouble codes are listed for a failed or faulty injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. Use these codes as part of diagnosis before replacing the injector.
Does this injector require coding or adaptation after installation?
Coding or adaptation requirements are not stated in the verified facts. Confirm the requirement against the vehicle's EPC instead of guessing.
How can I verify the old injector before ordering a replacement?
Check the old unit for part number JX6G-9F593-AA and compare it with cross references JX6G9F593AA, JX6Z9F593A, 0261500824, 0261500595, 0261500162, and 12698552. If the markings do not match, confirm fitment against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.