BOSCH JX6Z-9350-A
High Pressure Fuel Pump Ford Focus Mk4 Escape Bronco Sport 1.5T Dragon 0261520420
JX6G-9D376-AA, GDP110, 0261520420--200 bar peak rail pressureProduct Overview
The JX6Z-9350-A is an original equipment (BOSCH) precision component engineered specifically for the Ford 1.5L EcoBoost Dragon Ti-VCT Turbocharged DOHC 12V I3. Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P0191.
Always verify the OE reference JX6G9D376AA, GDP110 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. JX6Z-9350-A needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | JX6Z-9350-A |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Ford 1.5L EcoBoost Dragon Ti-VCT Turbocharged DOHC 12V I3 |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 12 N-m (106 lb-in) |
| Fuel Line / Rail Torque | 28 N-m (21 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P0191 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 12 N-m (106 lb-in), and torque fuel line fittings to 28 N-m (21 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify part number JX6Z-9350-A and the listed cross references against the vehicle’s EPC before installation.
- Tighten the pump mounting/hold-down to 12 N·m.
- Tighten the high-pressure line to 28 N·m.
Frequently Asked Questions
Will this pump fit my Ford Focus Mk4, Fiesta ST Mk8, or Kuga Mk3 with the 1.5L EcoBoost Dragon engine?
Listed fitment is Ford Focus Mk4 and Fiesta ST Mk8 with the Ford 1.5L EcoBoost Dragon (3-Cylinder Ti-VCT Turbo) for 2018-2023, plus Ford Kuga Mk3 with the same engine for 2019-2024. The part number is JX6Z-9350-A, and the listed cross references are JX6Z9350A, JX6G9D376AA, GDP110, 0261520420, and JX6G9F593AA. Confirm fitment against the vehicle’s EPC before ordering.
Does this high-pressure fuel pump require coding or adaptation after installation?
The provided facts do not state whether coding or adaptation is required for JX6Z-9350-A. Confirm any coding or adaptation requirement against the vehicle’s EPC instead of guessing.
Can the seals and high-pressure line be reused when fitting this pump?
The provided facts do not state whether the seals or high-pressure line can be reused with this gasoline direct-injection high-pressure fuel pump. Confirm the required replacement procedure against the vehicle’s EPC instead of guessing.
What diagnostic trouble codes are listed for this pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. Any further diagnostic criteria must be confirmed against the vehicle’s EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.