BOSCH 12636111
High Pressure Direct Fuel Injector GM Cadillac CTS Camaro Traverse Acadia Enclave 3.6L V6 LFX 0261500029
261500029, 12668649, 12634126, 217-3444, FJ1000, 0261500029HIGH-RESPONSE MULTI-HOLE ELECTROMAGNETIC HIGH-PRESSURE NOZZLE-150 bar peak rail pressureProduct Overview
The Bosch 12636111 (Bosch cross-reference 0261500029, GM superseded numbers 12668649 and 12634126) is the authentic Tier-1 original equipment high-pressure direct fuel injector engineered for General Motors' High Feature 3.6-liter LFX (and late LLT) direct-injection V6 engines. Installed across millions of Chevrolet Camaro, Cadillac CTS, ATS, SRX, Chevrolet Traverse, GMC Acadia, and Buick Enclave vehicles, this 150-bar (2175 psi) electromagnetic injector atomizes fuel straight into the combustion chamber to optimize fuel economy and throttle response. As mileage accumulates, carbon build-up and varnish gumming cause the internal needle pintle to stick, leading to drivability complaints. Technicians regularly diagnose trouble codes P0300 (Random Misfire), P0301 through P0306 (Cylinder 1-6 Misfire), and fuel trim codes P0171 / P0174 (Lean) or P0172 / P0175 (Rich). A dripping injector allows unburned fuel to wash cylinder walls and enter the catalytic converter, causing converter overheating and potential melt-down. Replacing injectors requires strict adherence to OEM clean-room practices. Fuel rail retaining bolts must be torqued to 10 N·m (89 in-lb), while fuel line flare union nuts require 30 N·m (22 lb-ft). Technicians must inspect spark plugs on affected cylinders and change engine oil if fuel dilution is present.
Always verify the OE reference 12668649, 12634126, 2173444, FJ1000 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 12636111 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | GM Spark Ignition Direct Injection (SIDI) 150-bar High-Pressure System |
| Operating PressureCore Spec | |
| Spray Configuration | Laser-Drilled 6-Hole Multi-Point Symmetrical Dispersion |
| Injector Hold-Down Bolt Torque | 10 N·m (89 in-lb) fuel rail mounting bolts📐 Torque & Angle Wizard → |
| Fuel Line Nut Torque | 30 N·m (22 lb-ft) high-pressure crossover tube union nut |
| Combustion Seal | High-Grade PTFE Virgin Teflon Combustion Ring |
| Upper Rail Sealing | Fluorocarbon (FKM) High-Temp Viton O-Ring |
| Manufacturer | Bosch (Tier-1 OEM for General Motors) |
| Bosch Production Number | 0261500029 |
Installation Tips
- High-Pressure System Residual Pressure Depressurization: Remove fuel pump relay from underhood fuse block. Crank engine for 5 seconds until it stalls, then disconnect negative battery terminal.
- Upper Intake Manifold & Plenum Removal: Disconnect throttle body harness, vacuum lines, and PCV tubes. Remove upper cast-aluminum intake manifold to expose cylinder head fuel rails.
- High-Pressure Fuel Crossover Pipe Disconnection: Loosen fuel crossover line union nuts using backup wrenches to prevent twisting fittings. Discard single-use flared pipe per GM service manuals.
- Fuel Rail Extraction & Injector Bore Cleaning: Unscrew rail hold-down bolts. Pull rails straight out along injector axis. Thoroughly clean carbon and varnish from cylinder head injector wells.
- Injector Installation & Torquing Sequence: Lightly oil upper Viton O-rings with clean engine oil (keep Teflon combustion seals dry). Seat injectors into rails, torque rail bolts to 10 N·m (89 in-lb), and line nuts to 30 N·m (22 lb-ft).
- Never reuse old Teflon combustion seals: The PTFE ring cold-flows during operation; reusing old seals causes combustion blow-by and burns cylinder head bores.
- Inspect spark plugs for fuel washing: Leaking direct injectors soak spark plugs, creating persistent misfires even after new injectors are installed.
- Always replace high-pressure fuel crossover pipe: GM high-pressure fuel lines use crush-type sealing interfaces designed strictly for single-use tightening.
- Verify low-pressure feed delivery: Check that the tank fuel pump maintains 4.5 to 5.5 bar (65 to 80 psi) under load before troubleshooting injectors.
Frequently Asked Questions
Does part number 12636111 fit my vehicle?
This gasoline direct-injection injector fits GM 3.6L High Feature V6 SIDI (LFX / LLT / LGX / LFY) applications: Chevrolet Camaro / Impala / Traverse (2012-2020); Cadillac CTS / ATS / SRX (2012-2016); and GMC Acadia (2012-2016). Confirm the exact application against your vehicle’s EPC before ordering.
What part numbers can I use to verify the old injector?
The part number is 12636111, and the listed cross references are 12636111, 261500029, 12668649, 12634126, 2173444, and FJ1000. Check the markings on the old unit and confirm against the vehicle’s EPC before replacement.
Which diagnostic trouble codes are listed for this injector?
The verified diagnostic trouble codes for this injector listing are P0300, P0301, P0087, P0302, and P0304. Any other fault code or symptom is not stated here and must be confirmed against the vehicle’s EPC rather than guessed.
What are the mounting and high-pressure line torque specs, and can I reuse the seals?
The mounting / hold-down torque is 10 N·m, and the high-pressure line torque is 30 N·m. The system pressure is 150 bar. Seal reuse is not stated in the verified facts and must be confirmed against the vehicle’s EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.