GM 12668635
SIDI Direct Fuel Injector Buick Enclave Chevrolet Blazer Traverse Cadillac XT6 3.6L V6 LGX
12668636, 12684125, 12684126, 217-3445, FJ1296--150 bar peak rail pressureProduct Overview
The 12668635 is an original equipment (GM) precision component engineered specifically for the General Motors 3.6L V6 DOHC 24V SIDI Direct Injection with AFM (LGX / LFY). Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0172, P0175.
Always verify the OE reference 12668636, 12684125, 12684126, 2173445 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 12668635 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 12668635 |
| Manufacturer Brand | GM |
| Component Type | Direct Fuel Injector |
| Engine Application | General Motors 3.6L V6 DOHC 24V SIDI Direct Injection with AFM (LGX / LFY) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 25 N-m (18 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0172, P0175 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 25 N-m (18 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the engine code and exact vehicle application against the EPC before opening the injector packaging.
- Handle the injector carefully and keep sealing surfaces clean, then verify any seal or coding requirement in the workshop manual.
- After installation, check for leaks and confirm correct operation using the vehicle's workshop diagnostic procedure.
Frequently Asked Questions
Which vehicles and engine families does part 12668635 fit?
It is listed for Chevrolet Camaro, Impala and Traverse; Cadillac CTS, ATS and SRX; and GMC Acadia with LFX, LLT, LGX or LFY engines. Confirm exact application against the vehicle EPC.
What symptoms suggest a failed gasoline direct-injection injector?
The listing does not specify failure symptoms; use the vehicle's workshop diagnostic data to confirm injector operation before ordering 12668635.
What should be checked before ordering this injector?
Verify the engine code shown on the vehicle, the original injector part number and connector style against the EPC or workshop manual, and confirm that 12668635 is the correct replacement.
Must the old injector be matched or adapted after replacement?
The listing does not state coding or adaptation requirements. Check the vehicle EPC or workshop manual for the required procedure before fitting 12668635.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.