BOSCH 12684225
High Pressure Fuel Injector Chevrolet Malibu Equinox Buick 1.5L Turbo SGE 0261500624
12668393, 12692283, 0261500624, 0261500625FAST-ACTUATING SOLENOID MULTI-HOLE DIRECT INJECTION NOZZLE-200 bar peak rail pressureProduct Overview
The Bosch 12684225 (Bosch 0261500624) is a Bosch HDEV5.2 multi-hole direct gasoline injector for GM 1.5L Ecotec turbo SIDI engines (LFV / LYX / L3G). It is listed for the Chevrolet Malibu XL 1.5 Turbo (2016-2023), Equinox 1.5 Turbo (2017-2023) and Buick Regal 1.5 Turbo (2017-2023). Nominal rail pressure is 200 bar (20 MPa / 2900 psi), with an optimized 6-orifice spray for central combustion ignition and coil resistance of 1.5-1.9 Ω at 20°C. Bracket clamping fasteners take 12 N·m and the high-pressure pipe flare nut 28 N·m. Common codes are P0300, P0301-P0304 and P0171. New Teflon combustion seals are installed with the EN-48266 seal expander tool.
Always verify the OE reference 12668393, 12692283 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 12684225 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDEV5.2 Multi-Hole Direct Gasoline Fuel Injector |
| Operating PressureCore Spec | |
| Spray Pattern | Optimized 6-orifice pattern for central combustion ignition |
| Fuel Rail Bolt Torque | 12 N·m (bracket clamping fasteners) |
| High Pressure Pipe Torque | 28 N·m Flare Nut Connection |
| Coil Resistance | 1.5 - 1.9 Ω at 20°C (Direct pulse solenoid control) |
| Common Fault Codes | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0171 (System Lean Bank 1) |
| Workshop Precaution | Install brand-new Teflon combustion seals using EN-48266 seal expander tool |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel Rail & Remove Intake Duct: Depressurize fuel system by removing fuel pump fuse and running engine until shutdown. Disconnect battery negative cable.
- Disconnect Fuel Rail Wire Connectors & Retainers: Disconnect injector electrical pigtails. Disconnect fuel feed pipe (28 N·m) and remove fuel rail retaining bolts (12 N·m).
- Extract Injectors & Renew Teflon Tip Seals: Carefully remove injectors from cylinder head bore using EN-47218 remover. Install new Teflon seals and size with calibration sleeve.
- Install Fuel Rail, Torque Bolts & Leak Check: Press injectors into cylinder head. Tighten rail bolts to 12 N·m. Torque fuel line nut to 28 N·m. Reconnect battery, prime system and inspect for leaks.
- Confirm the engine is a GM 1.5L Ecotec Turbo SIDI (LFV / LYX / L3G) before installing this injector.
- Tighten the injector mounting/hold-down to 12 N·m and the high-pressure line to 28 N·m.
- Check the old injector for 12684225 or the listed cross references before ordering a replacement.
Frequently Asked Questions
Will this injector fit my Chevrolet Malibu XL, Chevrolet Equinox, or Buick Regal 1.5 Turbo?
This gasoline direct-injection injector is listed for the GM 1.5L Ecotec Turbo SIDI engine family (LFV / LYX / L3G) and for Chevrolet Malibu XL 1.5 Turbo 1.5L Ecotec LFV 125kW (2016-2023), Chevrolet Equinox 1.5 Turbo 1.5L Ecotec LYX 125kW (2017-2023), and Buick Regal 1.5 Turbo 1.5L Ecotec LFV 125kW (2017-2023). Confirm the vehicle’s engine code and EPC listing before purchase.
What diagnostic trouble codes are listed for this injector?
The verified diagnostic trouble codes listed for this gasoline direct-injection injector are P0300, P0301, P0087, P0302, and P0304. Use these codes as diagnostic leads and confirm the faulty injector against the vehicle’s EPC/service information; no other symptoms are stated in the verified facts.
Does this injector require coding or adaptation after installation?
The verified facts do not state a coding or adaptation procedure for part number 12684225. Confirm injector coding/adaptation requirements against the vehicle’s EPC or service information instead of guessing.
How can I verify the old injector before ordering a replacement?
Check the old unit for part number 12684225 and compare it with the listed cross references 12668393, 12692283, 0261500624, 0261500625, and 0261500162. Confirm the engine family and vehicle fitment against the vehicle’s EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.